hi3516DV300烧录uboot后无法启动，求助！！！

用HiTool烧写的时候，只有显示下载成功，没有进一步启动UBoot。
################################# ---- 81%
################################# ---- 92%
########################## ---- 100%
Boot download completed!

正常情况下还会显示以下信息的
System startup

Uncompress Ok!

U-Boot 2016.11 (Mar 05 2019 - 21:42:34 +0800)hi3516dv300

Relocation Offset is: 0f6c2000
Relocating to 8fec2000, new gd at 8fe21ef0, sp at 8fe21ed0

正常打印信息 类似


串口已经连接，请给单板上电，若已经上电，请断电后重新上电。
################################# ---- 10%
################################ ---- 20%
################################ ---- 30%
################################ ---- 41%
################################ ---- 51%
################################ ---- 61%
################################ ---- 72%
################################ ---- 82%
################################ ---- 92%
####################### ---- 100%
Boot download completed!

System startup


U-Boot 2010.06 (Sep 07 2018 - 01:53:16)

Check Flash Memory Controller v100 ... Found
SPI Nor(cs 0) ID: 0xc2 0x20 0x18
Block:64KB Chip:16MB Name:"MX25L128XX"
SPI Nor total size: 16MB
MMC:   
EMMC/MMC/SD controller initialization.
Card did not respond to voltage select!
No EMMC/MMC/SD device found !
In:    serial
Out:   serial
Err:   serial
start download process.

Boot started successfully!

Send command:    getinfo version
version: 3.0.3
[EOT](OK)

Send command:    getinfo bootmode
spi
[EOT](OK)

Send command:    sf probe 0
16384 KiB hi_fmc at 0:0 is now current device
[EOT](OK)

Send command:    getinfo spi
Block:64KB Chip:16MB*1
ID:0xC2 0x20 0x18
Name:"MX25L128XX"
[EOT](OK)

Send command:    sf probe 0
16384 KiB hi_fmc at 0:0 is now current device
[EOT](OK)

Send command:    sf erase 0x0 0x50000

Erasing at 0x10000 --  20% complete.
Erasing at 0x20000 --  40% complete.
Erasing at 0x30000 --  60% complete.
Erasing at 0x40000 --  80% complete.
Erasing at 0x50000 -- 100% complete.
[EOT](OK)

Send command:    sf write 0x81000000 0x0 0x50000

Writing at 0x10000 --  20% complete.
Writing at 0x20000 --  40% complete.
Writing at 0x30000 --  60% complete.
Writing at 0x40000 --  80% complete.
Writing at 0x50000 -- 100% complete.
[EOT](OK)

Send command:    reset
reset success!
Boot burned successfully.

看似DDR3  没有正常工作？  还是UBOOT文件不匹配？

hi3516DV300烧录uboot失败，求助！！！

问题解决了，uboot文件不对。Hi3516DV300-DMEBPRO_6L_T-DDR3_1800M_1GB_16bitx2-A7_900M-SYSBUS_300M 硬件电路设计参考是这个，  UBOOT设计应该参考这个。  

默认的UBOOT是这个配置：
附件：1.png

软件那边只有个4层板配置文件，硬件是按六层板设计的

Platform Version: 5.0.58
HiBurn Version: 5.0.58
HiSilicon Technologies Co., Ltd. All rights reserved. (C) 2011-2018


Platform Version: 5.0.58
HiBurn Version: 5.0.58
HiSilicon Technologies Co., Ltd. All rights reserved. (C) 2011-2018



串口已经连接，请给单板上电，若已经上电，请断电后重新上电。
############################### ---- 10%
############################## ---- 20%
############################## ---- 30%
############################## ---- 41%
############################## ---- 51%
############################## ---- 61%
############################## ---- 72%
############################## ---- 82%
############################## ---- 92%
##################### ---- 100%
Boot download completed!
     

System startup

Uncompress Ok!

U-Boot 2016.11 (Jun 12 2020 - 16:11:58 +0800)hi3516dv300

Relocation Offset is: 0f6d8000
Relocating to 8fed8000, new gd at 8fe37ef0, sp at 8fe37ed0
MMC:   
EMMC/MMC/SD controller initialization.
scan edges:2 p2f:6 f2p:1
mix set temp-phase 3

System startup

Uncompress Ok!

U-Boot 2016.11 (Jun 12 2020 - 16:11:58 +0800)hi3516dv300

Relocation Offset is: 0f6d8000
Relocating to 8fed8000, new gd at 8fe37ef0, sp at 8fe37ed0
MMC:   
EMMC/MMC/SD controller initialization.
scan edges:2 p2f:7 f2p:1
mix set temp-phase 4
scan elemnts: startp:11 endp:128
Tuning SampleClock. mix set phase:[04/07] ele:[05/16]
** First descriptor is NOT a primary desc on 0:1 **
MMC/SD Card:
    MID:         0x15
    Read Block:  512 Bytes
    Write Block: 512 Bytes
    Chip Size:   7456M Bytes (High Capacity)
    Name:        "8GTF4"
    Chip Type:   MMC
    Version:     0.0
    Speed:       100000000Hz
    Bus Width:   4bit
himci: 0 (eMMC)
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   eth0
Warning: eth0 (eth0) using random MAC address - 7a:50:93:73:7a:c6

Hit any key to stop autoboot:  0

MMC read: dev # 0, block # 2048, count 10240 .

[quote][url=forum.php?mod=redirect&goto=findpost&pid=159717&ptid=80629]y2006142108 发表于 2020-6-12 17:16[/url]
问题解决了，uboot文件不对。Hi3516DV300-DMEBPRO_6L_T-DDR3_1800M_1GB_16bitx2-A7_900M-SYSBUS_300M 硬件 ...[/quote]

2019-03-11  18:51           276,830 Hi3516AV300-DDR4DMEB_4L_T-DDR4_2133M_1GB_16bitX2-A7_900M-SYSBUS_300M.xlsm
2019-03-11  18:52           261,432 Hi3516AV300-DMEBLITE_6L_T-DDR4_2133M_1GB_16bitx2-A7_900M-SYSBUS_300M.xlsm
2019-03-11  18:45           277,023 Hi3516AV300-DMEB_4L_FLYBY-DDR3_1800M_1GB_16bitx2-A7_900M-SYSBUS_300M.xlsm
2019-03-11  17:36           260,767 Hi3516CV500-DDR4DMEB_4L-DDR4_1800M_512MB_16bit-A7_900M-SYSBUS_300M.xlsm
2019-03-11  18:52           276,684 Hi3516DV300-DDR4DMEB_4L_T-DDR4_1800M_1GB_16bitX2-A7_900M-SYSBUS_300M.xlsm
2019-03-11  17:34           261,220 Hi3516DV300-DMEBLITE_6L_T-DDR4_1800M_1GB_16bitx2-A7_900M-SYSBUS_300M.xlsm
2019-03-11  19:36           277,131 Hi3516DV300-DMEBPRO_6L_T-DDR3_1800M_1GB_16bitx2-A7_900M-SYSBUS_300M.xlsm
2019-01-15  13:56           254,689 Naming Rules of a U-Boot Table.pdf
2019-01-15  13:56           378,868 uboot 表格命名规则.pdf
              10 个文件      2,525,844 字节
               2 个目录 418,450,665,472 可用字节

Hi3516AV300-DDR4DMEB_4L_T-DDR4_2133M_1GB_16bitX2-A7_900M-SYSBUS_300M.xlsm
Hi3516AV300-DMEBLITE_6L_T-DDR4_2133M_1GB_16bitx2-A7_900M-SYSBUS_300M.xlsm
Hi3516AV300-DMEB_4L_FLYBY-DDR3_1800M_1GB_16bitx2-A7_900M-SYSBUS_300M.xlsm
Hi3516CV500-DDR4DMEB_4L-DDR4_1800M_512MB_16bit-A7_900M-SYSBUS_300M.xlsm
Hi3516DV300-DDR4DMEB_4L_T-DDR4_1800M_1GB_16bitX2-A7_900M-SYSBUS_300M.xlsm
Hi3516DV300-DMEBLITE_6L_T-DDR4_1800M_1GB_16bitx2-A7_900M-SYSBUS_300M.xlsm
Hi3516DV300-DMEBPRO_6L_T-DDR3_1800M_1GB_16bitx2-A7_900M-SYSBUS_300M.xlsm

本帖最后由 y2006142108 于 2020-6-12 19:23 编辑

SPI NOR FLASH



串口已经连接，请给单板上电，若已经上电，请断电后重新上电。
############################### ---- 10%
############################## ---- 20%
############################## ---- 30%
############################## ---- 41%
############################## ---- 51%
############################## ---- 61%
############################## ---- 72%
############################## ---- 82%
############################## ---- 92%
##################### ---- 100%
Boot download completed!
     

System startup

Uncompress Ok!

U-Boot 2016.11 (Jun 12 2020 - 16:11:58 +0800)hi3516dv300

Relocation Offset is: 0f6c0000
Relocating to 8fec0000, new gd at 8fe1fef0, sp at 8fe1fed0
SPI Nor:  hifmc_ip_ver_check(44): Check Flash Memory Controller v100 ...hifmc_ip_ver_check(50):  Found
hifmc_spi_nor_probe(1664): SPI Nor ID Table Version 1.0
hifmc_spi_nor_probe(1689): SPI Nor(cs 0) ID: 0x1 0x2 0x19 0x4d 0x1 0x80
hifmc_spi_nor_probe(1754): Block:64KB hifmc_spi_nor_probe(1755): Chip:32MB hifmc_spi_nor_probe(1756): Name:"S25FL256S"
hifmc100_spi_nor_probe(147): SPI Nor total size: 32MB
NAND:  0 MiB
MMC:   
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   eth0
Warning: eth0 (eth0) using random MAC address - 8e:46:f3:b5:70:eb

start download process.

Boot started successfully!

Send command:        getinfo version
version: U-Boot 2016.11
[EOT](OK)

Send command:        getinfo bootmode
spi
[EOT](OK)

Send command:        sf probe 0
[EOT](OK)

Send command:        getinfo spi
Block:64KB Chip:32MB*1
ID:0x01 0x02 0x19 0x4D 0x01 0x80
Name:"S25FL256S"
[EOT](OK)

Send command:        sf probe 0
[EOT](OK)

Send command:        sf erase 0x0 0x50000

Erasing at 0x10000 --  20% complete.
Erasing at 0x20000 --  40% complete.
Erasing at 0x30000 --  60% complete.
Erasing at 0x40000 --  80% complete.
Erasing at 0x50000 -- 100% complete.
SF: 327680 bytes @ 0x0 Erased: OK
[EOT](OK)

Send command:        sf write 0x81000000 0x0 0x50000
device 0 offset 0x0, size 0x50000

Writing at 0x10000 --  20% complete.
Writing at 0x20000 --  40% complete.
Writing at 0x30000 --  60% complete.
Writing at 0x40000 --  80% complete.
Writing at 0x50000 -- 100% complete.
SF: 327680 bytes @ 0x0 Written: OK
[EOT](OK)

Send command:        reset
reset success!
Boot burned successfully.

我使用的是Hi3516DV300，开发板是：
HiSpark AI Camera套件

使用的SDK是：Hi3516CV500R001C02SPC021
压缩包是：Hi3516CV500_SDK_V2.0.2.1.tgz。

不知道您是否调通这一片开发板！或者将您的XLSM配置文件共享一下！
多谢了！

DDR那边有问题的可能性比较大

我也碰到了这个问题，请教怎样修改DDR的参数呢？我SDK只有一份EXCEL档
Hi3516DV300-DMEB_4L_FLYBY-DDR3_1800M_512MB_16bitx2-A7_900M-SYSBUS_300M.xlsm

请问这个些文件在哪边可以下载嘛？

引用 @y2006142108 “[quote][url=forum.ph”

Boot download completed!
等待boot启动超时，单板上无fastboot或当前fastboot无法启动。
有人遇到这个问题并解决了吗

这里并没有烧录成功，只是加载进了服务，还没进行烧录。