从放弃到入门[三]:烧录海思Hi3516EV200

codinglab 2020-09-12 15:07:52 14314

从放弃到入门[三]:烧录海思Hi3516EV200

写在前面:从放弃到入门系列的第二弹中,小A已经完成SDK的整体编译了。那么仅仅编译出来是不够的,我们还要实际运行验证编译结果,因此一般情况下我们需要先烧录uboot,kernel,rootfs到存储器中,组成一个完整的小系统,然后基于此我们才能进行后续的学习。

小A以前在学习嵌入式的过程中,遇到的常见烧录方法有JTAG烧录,有串口烧录,有网口烧录,也有通过usb口使用DNW烧录,这些方式都各有各的特色和应用场景。下面以spi nand为例,来看看海思平台下的烧录方法。

海思提供了一个烧录工具HiTool,通过这个工具我们可以简单快速的完成海思平台的各类烧录需求。HiTool在正式使用前,一定要正确选择当前芯片,可以通过界面左上角的芯片选项卡进行切换目标芯片。

以Hi3516EV200为例,HiTool囊括了常见的串口方式烧录,网口方式烧录以及USB方式烧录。另外海思平台的烧录方式有裸烧和非裸烧两种,二者的主要区别是烧录时勾不勾选u-boot分区。

一. 串口烧录

场景:因为受限于串口的数据传输速率,如果用串口方式全片烧录8M spi nor的话,大概需要十多分钟才能完成,一般串口烧录只用于烧写fastboot(u-boot),在u-boot调试过程中使用较为方便。

案例:通过串口烧录fastboot。

原理:HiBurn 工具在开始烧写后,首选与 bootrom 进行交互,工具 DDR 参数传送到传到 bootrom,然后初始化 DDR,再把 uboot 传输到 DDR 中,再从 DDR 启动 uboot,uboot 启动完成后,工具开始与 uboot 进行交互,发送烧写命令,将 DDR 中的 uboot 烧写到Flash 对应地址中。

烧录日志如下:

串口已经连接,请给单板上电,若已经上电,请断电后重新上电。
############################ ---- 10%
########################### ---- 20%
########################### ---- 30%
########################### ---- 41%
########################### ---- 51%
########################### ---- 61%
########################### ---- 71%
########################### ---- 82%
########################### ---- 92%
##################### ---- 100%
Boot download completed!

System startup

Uncompress Ok!

U-Boot 2016.11-ge0aea76-dirty (Jun 06 2020 - 20:45:07 +0800)hi3516ev200

Relocation Offset is: 03734000
Relocating to 43f34000, new gd at 43e93ef0, sp at 43e93ed0
SPI Nor:  Boot Media isn't SPI Nor
NAND:  SPI Nand ID Table Version 2.7
SPI Nand(cs 0) ID: 0xef 0xaa 0x21 Name:"W25N01GV"
Block:128KB Page:2KB OOB:64B ECC:4bit/512 
Chipsize:128 MiB
MMC:   
In:    serial
Out:   serial
Err:   serial
Net:   eth0
start download process.

Boot started successfully!

Send command:   getinfo version
version: U-Boot 2016.11-ge0aea76-dirty
[EOT](OK)

Send command:   getinfo bootmode
nand
[EOT](OK)

Send command:   getinfo nand
Block:128KB Chip:128MB*1 Page:2KB OOB:64B ECC:4bit/512 
ID:0xEF 0xAA 0x21 
Name:"W25N01GV"
[EOT](OK)

Send command:   nand erase 0x0 0x40000

NAND erase: device 0 offset 0x0, size 0x40000

Erasing at 0x0 --  50% complete.
Erasing at 0x20000 -- 100% complete.
OK
[EOT](OK)

Send command:   nand write 0x41000000 0x0 0x40000

NAND write: device 0 offset 0x0, size 0x40000
pure data length  262144 bytes written: OK
[EOT](OK)

Send command:   reset
reset success!
Boot burned successfully.

从上面的日志输出可以看到uboot的烧录流程和uboot的烧录原理是吻合的,总耗时大约80秒左右。

二. 网口烧录

场景:一般嵌入式平台网口烧录,都是通过串口在u-boot命令行下配置好网络参数然后通过tftp进行下载和写入,所以网口烧录一般用于烧录uboot之外的其它镜像。

原理:同样的,HiTool基本也是这个原理,HiTool内置了tftp服务。所以虽然是网口烧录,但是同时也要配置好串口。HiTool通过串口与uboot进行交互,下发tftp指令和write指令,完成烧写。所以选择网口烧录的时候,既要选对pc的串口和服务器ip,还要保证服务器ip和板端配置的ip地址必须要在同一个局域网段才可以,否则无法完成网口烧录。

案例:烧录kernel和rootfs

烧录日志如下:

串口已经连接,请给单板上电,若已经上电,请断电后重新上电。
# ---- 33%
# ---- 100%
Boot download completed!

System startu 

Uncompress Ok!

U-Boot 2016.11-ge0aea76-dirty (Jun 06 2020 - 20:45:07 +0800)hi3516ev200

Relocation Offset is: 03734000
Relocating to 43f34000, new gd at 43e93ef0, sp at 43e93ed0
SPI Nor:  Boot Media isn't SPI Nor
NAND:  SPI Nand ID Table Version 2.7
SPI Nand(cs 0) ID: 0xef 0xaa 0x21 Name:"W25N01GV"
Block:128KB Page:2KB OOB:64B ECC:4bit/512 
Chipsize:128 MiB
MMC:   
In:    serial
Out:   serial
Err:   serial
Net:   eth0
start download process.

Boot started successfully!

Send command:   getinfo version
version: U-Boot 2016.11-ge0aea76-dirty
[EOT](OK)

Send command:   getinfo nand
Block:128KB Chip:128MB*1 Page:2KB OOB:64B ECC:4bit/512 
ID:0xEF 0xAA 0x21 
Name:"W25N01GV"
[EOT](OK)
waiting phy ready, it will take 8s.

Send command:   setenv serverip 192.168.3.2
[EOT](OK)

Send command:   setenv ethaddr 00:00:00:00:00:01
[EOT](OK)

Send command:   setenv ipaddr 192.168.3.99
[EOT](OK)

Send command:   setenv netmask 255.255.255.0
[EOT](OK)

Send command:   setenv gatewayip 192.168.3.1
[EOT](OK)
    Tftp server Download Home switched to <\\DS220plus\synology\burn_test>

Send command:   mw.b 0x41000000 0xFF 0x3a0000
[EOT](OK)

Send command:   tftp 0x41000000 uImage
Hisilicon ETH net controler
eth0 : phy status change : LINK=UP : DUPLEX=FULL : SPEED=100M
Using eth0 device
TFTP from server 192.168.3.2; our IP address is 192.168.3.99
Filename 'uImage'.
Load address: 0x41000000
Loading: *##########################################################################################################################
     #######################################################################################################################
     #######################################################################################################################
     #########################################################################################################
     393.6 KiB/s
done
Bytes transferred = 3699632 (3873b0 hex)
[EOT](OK)

Send command:   crc32 41000000 3873b0
crc32 for 41000000 ... 413873af ==> 4151880d
[EOT](OK)

Send command:   nand erase 0x80000 0x500000

NAND erase: device 0 offset 0x80000, size 0x500000

Erasing at 0x80000 --   2% complete.
Erasing at 0xa0000 --   5% complete.
Erasing at 0xc0000 --   7% complete.
Erasing at 0xe0000 --  10% complete.
Erasing at 0x100000 --  12% complete.
Erasing at 0x120000 --  15% complete.
Erasing at 0x140000 --  17% complete.
Erasing at 0x160000 --  20% complete.
Erasing at 0x180000 --  22% complete.
Erasing at 0x1a0000 --  25% complete.
Erasing at 0x1c0000 --  27% complete.
Erasing at 0x1e0000 --  30% complete.
Erasing at 0x200000 --  32% complete.
Erasing at 0x220000 --  35% complete.
Erasing at 0x240000 --  37% complete.
Erasing at 0x260000 --  40% complete.
Erasing at 0x280000 --  42% complete.
Erasing at 0x2a0000 --  45% complete.
Erasing at 0x2c0000 --  47% complete.
Erasing at 0x2e0000 --  50% complete.
Erasing at 0x300000 --  52% complete.
Erasing at 0x320000 --  55% complete.
Erasing at 0x340000 --  57% complete.
Erasing at 0x360000 --  60% complete.
Erasing at 0x380000 --  62% complete.
Erasing at 0x3a0000 --  65% complete.
Erasing at 0x3c0000 --  67% complete.
Erasing at 0x3e0000 --  70% complete.
Erasing at 0x400000 --  72% complete.
Erasing at 0x420000 --  75% complete.
Erasing at 0x440000 --  77% complete.
Erasing at 0x460000 --  80% complete.
Erasing at 0x480000 --  82% complete.
Erasing at 0x4a0000 --  85% complete.
Erasing at 0x4c0000 --  87% complete.
Erasing at 0x4e0000 --  90% complete.
Erasing at 0x500000 --  92% complete.
Erasing at 0x520000 --  95% complete.
Erasing at 0x540000 --  97% complete.
Erasing at 0x560000 -- 100% complete.
OK
[EOT](OK)

Send command:   nand write 0x41000000 0x80000 0x3a0000

NAND write: device 0 offset 0x80000, size 0x3a0000
pure data length is 3801088, l 3801088 bytes written: OK
[EOT](OK)
Partition kernel burnt successfully!
    Tftp server Download Home switched to <\\DS220plus\synology\burn_test>

Send command:   getinfo nand
Block:128KB Chip:128MB*1 Page:2KB OOB:64B ECC:4bit/512 
ID:0xEF 0xAA 0x21 
Name:"W25N01GV"
[EOT](OK)

Send command:   mw.b 0x41000000 0xFF 0x1fd9940
[EOT](OK)

Send command:   tftp 0x41000000 yaffs2-128M-3516ev200.img
Hisilicon ETH net controler
eth0 : phy status change : LINK=UP : DUPLEX=FULL : SPEED=100M
Using eth0 device
TFTP from server 192.168.3.2; our IP address is 192.168.3.99
Filename 'yaffs2-128M-3516ev200.img'.
Load address: 0x41000000
Loading: *#################################################################################################################
     #######################################################################################################################
     ######################################################################################################################
     #######################################################################################################################
     ###################################################################################################################
     #####################################################################################################################
     #####################################################################################################################
     #########################################################################################################################
     ##########################################################################################################################
     ########################################################################################################################
     ######################################################################################################################
     #######################################################################################################################
     #########################################################################################################################
     #########################################################################################################################
     ####################################################################################################################
     ###################################################################################################################
     ####################################################################################################################
     ########################################################################################################################
     #####################################################################################################################
     #########################################################################################################################
     ######################################################################################################################
     #########################################################################################################################
     ############################################################################################################################
     #####################################################################################################################
     #####################################################################################################################
     #####################################################################################################################
     #####################################################################################################################
     ######################################################################################################################
     #######################################################################################################################
     ######################################################################################################################
     ######################################################################################################################
     ##########################################################################################################################
     ####################################################################################################################
     ########################################################################################################################
     #######################################################################################################################
     #
     790 KiB/s
done
Bytes transferred = 33397056 (1fd9940 hex)
[EOT](OK)

Send command:   crc32 41000000 1fd9940
crc32 for 41000000 ... 42fd993f ==> a0ba3513
[EOT](OK)

Send command:   nand erase 0x580000 0x7a80000

NAND erase: device 0 offset 0x580000, size 0x7a80000

Erasing at 0x580000 --   0% complete.
Erasing at 0x6a0000 --   1% complete.
Erasing at 0x7e0000 --   2% complete.
Erasing at 0x920000 --   3% complete.
Erasing at 0xa60000 --   4% complete.
Erasing at 0xb80000 --   5% complete.
Erasing at 0xcc0000 --   6% complete.
Erasing at 0xe00000 --   7% complete.
Erasing at 0xf40000 --   8% complete.
Erasing at 0x1080000 --   9% complete.
Erasing at 0x11a0000 --  10% complete.
Erasing at 0x12e0000 --  11% complete.
Erasing at 0x1420000 --  12% complete.
Erasing at 0x1560000 --  13% complete.
Erasing at 0x16a0000 --  14% complete.
Erasing at 0x17c0000 --  15% complete.
Erasing at 0x1900000 --  16% complete.
Erasing at 0x1a40000 --  17% complete.
Erasing at 0x1b80000 --  18% complete.
Erasing at 0x1cc0000 --  19% complete.
Erasing at 0x1de0000 --  20% complete.
Erasing at 0x1f20000 --  21% complete.
Erasing at 0x2060000 --  22% complete.
Erasing at 0x21a0000 --  23% complete.
Erasing at 0x22e0000 --  24% complete.
Erasing at 0x2400000 --  25% complete.
Erasing at 0x2540000 --  26% complete.
Erasing at 0x2680000 --  27% complete.
Erasing at 0x27c0000 --  28% complete.
Erasing at 0x2900000 --  29% complete.
Erasing at 0x2a20000 --  30% complete.
Erasing at 0x2b60000 --  31% complete.
Erasing at 0x2ca0000 --  32% complete.
Erasing at 0x2de0000 --  33% complete.
Erasing at 0x2f20000 --  34% complete.
Erasing at 0x3040000 --  35% complete.
Erasing at 0x3180000 --  36% complete.
Erasing at 0x32c0000 --  37% complete.
Erasing at 0x3400000 --  38% complete.
Erasing at 0x3540000 --  39% complete.
Erasing at 0x3660000 --  40% complete.
Erasing at 0x37a0000 --  41% complete.
Erasing at 0x38e0000 --  42% complete.
Erasing at 0x3a20000 --  43% complete.
Erasing at 0x3b60000 --  44% complete.
Erasing at 0x3c80000 --  45% complete.
Erasing at 0x3dc0000 --  46% complete.
Erasing at 0x3f00000 --  47% complete.
Erasing at 0x4040000 --  48% complete.
Erasing at 0x4180000 --  49% complete.
Erasing at 0x42a0000 --  50% complete.
Erasing at 0x43e0000 --  51% complete.
Erasing at 0x4520000 --  52% complete.
Erasing at 0x4660000 --  53% complete.
Erasing at 0x47a0000 --  54% complete.
Erasing at 0x48c0000 --  55% complete.
Erasing at 0x4a00000 --  56% complete.
Erasing at 0x4b40000 --  57% complete.
Erasing at 0x4c80000 --  58% complete.
Erasing at 0x4dc0000 --  59% complete.
Erasing at 0x4ee0000 --  60% complete.
Erasing at 0x5020000 --  61% complete.
Erasing at 0x5160000 --  62% complete.
Erasing at 0x52a0000 --  63% complete.
Erasing at 0x53e0000 --  64% complete.
Erasing at 0x5500000 --  65% complete.
Erasing at 0x5640000 --  66% complete.
Erasing at 0x5780000 --  67% complete.
Erasing at 0x58c0000 --  68% complete.
Erasing at 0x5a00000 --  69% complete.
Erasing at 0x5b20000 --  70% complete.
Erasing at 0x5c60000 --  71% complete.
Erasing at 0x5da0000 --  72% complete.
Erasing at 0x5ee0000 --  73% complete.
Erasing at 0x6020000 --  74% complete.
Erasing at 0x6140000 --  75% complete.
Erasing at 0x6280000 --  76% complete.
Erasing at 0x63c0000 --  77% complete.
Erasing at 0x6500000 --  78% complete.
Erasing at 0x6640000 --  79% complete.
Erasing at 0x6760000 --  80% complete.
Erasing at 0x68a0000 --  81% complete.
Erasing at 0x69e0000 --  82% complete.
Erasing at 0x6b20000 --  83% complete.
Erasing at 0x6c60000 --  84% complete.
Erasing at 0x6d80000 --  85% complete.
Erasing at 0x6ec0000 --  86% complete.
Erasing at 0x7000000 --  87% complete.
Erasing at 0x7140000 --  88% complete.
Erasing at 0x7280000 --  89% complete.
Erasing at 0x73a0000 --  90% complete.
Erasing at 0x74e0000 --  91% complete.
Erasing at 0x7620000 --  92% complete.
Erasing at 0x7760000 --  93% complete.
Erasing at 0x78a0000 --  94% complete.
Erasing at 0x79c0000 --  95% complete.
Erasing at 0x7b00000 --  96% complete.
Erasing at 0x7c40000 --  97% complete.
Erasing at 0x7d80000 --  98% complete.
Erasing at 0x7ec0000 --  99% complete.
Erasing at 0x7fe0000 -- 100% complete.
OK
[EOT](OK)

Send command:   nand write.yaffs 0x41000000 0x580000 0x1fd9940

NAND write: device 0 offset 0x580000, size 0x1fd9940
pure data length is 32385024, len_incl_bad is 32385024
NAND write yaffs finished
 33397056 bytes written: OK
[EOT](OK)
Partition rootfs burnt successfully!

Send command:   reset
reset success!
Partition burnt completed!

从上面的日志大致可以看出网口烧录时,HiTool会在uboot启动后,先根据我们设置好的板端参数进行bootenv的设置,然后再进行tftp下载和write的操作,全程不必手动敲命令,简单快捷,整个过程持续了大概80秒左右。

三. USB烧录

USB烧录的典型工具就是DNW,这个工具有些小伙伴可能都听过。使用USB烧录,需要先安装好usb驱动。
驱动安装:
在uboot命令行下输入命令:

usb device

没有安装驱动的情况下,在pc的设备管理器中会出现一个异常设备HiUSBBurn,如下图所示。

然后打开下载好的zadig-2.5.exe(传送门),选择设备HiUSBBurn,选择驱动libusbK进行安装。

安装好后会看到:

案例:烧录kernel和rootfs

烧录日志如下:

# ---- 33%
# ---- 100%
Boot download completed!
start download process.
Boot started successfully!

Send command:   getinfo version
version: U-Boot 2016.11-ge0aea76-dirty
[EOT](OK)

Send command:   getinfo nand
Block:128KB Chip:128MB*1 Page:2KB OOB:64B ECC:4bit/512 
ID:0xEF 0xAA 0x21 
Name:"W25N01GV"
[EOT](OK)

Send command:   mw.b 0x41000000 0xFF 0x3a0000
[EOT](OK)

Send command:   Downloading File : uImage

[Download File by usb]
file = \\DS220plus\synology\burn_test\uImage
address = 0x41000000
fileLength = 3699632 B
#
done

Send command:   nand erase 0x80000 0x500000

NAND erase: device 0 offset 0x80000, size 0x500000

Erasing at 0x80000 --   2% complete.
Erasing at 0xa0000 --   5% complete.
Erasing at 0xc0000 --   7% complete.
Erasing at 0xe0000 --  10% complete.[EOT](OK)

Send command:   nand write 0x41000000 0x80000 0x3a0000

NAND write: device 0 offset 0x80000, size 0x3a0000
pure data length is 3801088, len_incl_bad is 3801088
 3801088 bytes written: OK
[EOT](OK)
Partition kernel burnt successfully!

Send command:   getinfo nand
Block:128KB Chip:128MB*1 Page:2KB OOB:64B ECC:4bit/512 
ID:0xEF 0xAA 0x21 
Name:"W25N01GV"
[EOT](OK)

Send command:   mw.b 0x41000000 0xFF 0x1fd9940
[EOT](OK)

Send command:   Downloading File : yaffs2-128M-3516ev200.img

[Download File by usb]
file = \\DS220plus\synology\burn_test\yaffs2-128M-3516ev200.img
address = 0x41000000
fileLength = 33397056 B
########
done

Send command:   nand erase 0x580000 0x7a80000

NAND erase: device 0 offset 0x580000, size 0x7a80000

Erasing at 0x580000 --   0% complete.
Erasing at 0x6a0000 --   1% complete.
Erasing at 0x7e0000 --   2% complete.
Erasing at 0x920000 --   3% complete.[EOT](OK)

Send command:   nand write.yaffs 0x41000000 0x580000 0x1fd9940

NAND write: device 0 offset 0x580000, size 0x1fd9940
pure data length is 32385024, len_incl_bad is 32385024
NAND write yaffs finished
 33397056 bytes written: OK
[EOT](OK)
Partition rootfs burnt successfully!

Send command:   reset
reset success!
Partition burnt completed!

USB channels were closed successfully.

整体大致流程和网口烧录差不多,主要区别在于下载方式的不同,一个是网口,一个是usb口。整体耗时42s。

四.总结

通过以上常用的烧录方式对比,串口烧录虽然慢,但是考虑到硬件设计,比如usb口设计为板载wifi,再比如3518ev300没有phy,所以它是必不可少的。在条件允许的情况下,小A还是喜欢通过usb烧录,因为它更简单(相比较网口烧录,无需来回切换串口中断),快速。

HiTool除了上述烧录功能外,还有合并镜像和上载镜像两大功能,小A今天就不展开了,以后再说吧。更多内容请参考《HiBurn工具使用指南》。

声明:本文内容由易百纳平台入驻作者撰写,文章观点仅代表作者本人,不代表易百纳立场。如有内容侵权或者其他问题,请联系本站进行删除。
红包 2 收藏 评论 打赏
评论
1个
内容存在敏感词
手气红包
  • 烈日灼心 2020-09-14 14:04:37
    回复

    赞,感谢大神分享!

相关专栏
置顶时间设置
结束时间
删除原因
  • 广告/SPAM
  • 恶意灌水
  • 违规内容
  • 文不对题
  • 重复发帖
打赏作者
易百纳技术社区
codinglab
您的支持将鼓励我继续创作!
打赏金额:
¥1易百纳技术社区
¥5易百纳技术社区
¥10易百纳技术社区
¥50易百纳技术社区
¥100易百纳技术社区
支付方式:
微信支付
支付宝支付
易百纳技术社区微信支付
易百纳技术社区
打赏成功!

感谢您的打赏,如若您也想被打赏,可前往 发表专栏 哦~

举报反馈

举报类型

  • 内容涉黄/赌/毒
  • 内容侵权/抄袭
  • 政治相关
  • 涉嫌广告
  • 侮辱谩骂
  • 其他

详细说明

审核成功

发布时间设置
发布时间:
是否关联周任务-专栏模块

审核失败

失败原因
备注
拼手气红包 红包规则
祝福语
恭喜发财,大吉大利!
红包金额
红包最小金额不能低于5元
红包数量
红包数量范围10~50个
余额支付
当前余额:
可前往问答、专栏板块获取收益 去获取
取 消 确 定

小包子的红包

恭喜发财,大吉大利

已领取20/40,共1.6元 红包规则

    易百纳技术社区