Loading...
Hi3518ev300 配置RTL8189时 最后连不上WiFi了
长歌行丶  发布于 07/16 19:30
浏览 61

./wpa_supplicant -i wlan0 -D nl80211 -c /etc/wpa_supplicant.conf -B运行后
这是打印的log
wpa_supplicant v0.8.x_rtw_r24647.20171025
random: Trying to read entropy from /dev/random
Initializing interface ‘wlan0’ conf ‘/etc/wpa_supplicant.conf’ driver ‘nl80211’ ctrl_interface ‘N/A’ bridge ‘N/A’
Configuration file ‘/etc/wpa_supplicant.conf’ -> ‘/etc/wpa_supplicant.conf’
Reading configuration file ‘/etc/wpa_supplicant.conf’
ctrl_interface=’/var/run/wpa_supplicant’
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=7):
5a 58 43 5a 39 31 32 ZXCZ912
PSK - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid=’ZXCZ912’
nl80211: interface wlan0 in phy phy0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
netlink: Operstate: linkmode=1, operstate=5
nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)
nl80211: Register frame match - hexdump(len=1): 06
nl80211: Failed to register Action frame processing - ignore for now
nl80211: driver param=’(null)’
wlan0: Own MAC address: 7c:a7:b0:50:56:65
wpa_driver_nl80211_set_key: ifindex=2 alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=2 alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=2 alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=2 alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
wlan0: RSN: flushing PMKID list in the driver
wlan0: Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
Using existing control interface directory.
ctrl_iface bind(PF_UNIX) failed: Address already in use
ctrl_iface exists and seems to be in use - cannot override it
Delete ‘/var/run/wpa_supplicant/wlan0’ manually if it is not used anymore
Failed to initialize control interface ‘/var/run/wpa_supplicant’.
You may have another wpa_supplicant process already running or the file was
left by an unclean termination of wpa_supplicant in which case you will need
to manually remove this file before starting wpa_supplicant again.

Failed to add interface wlan0
wlan0: No keys have been configured - skip key clearing
wlan0: State: DISCONNECTED -> DISCONNECTED
wpa_driver_nl80211_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
wlan0: No keys have been configured - skip key clearing
wlan0: Cancelling scan request
wlan0: Cancelling authentication timeout
netlink: Operstate: linkmode=0, operstate=6

收藏0
0个回答
内容存在敏感词
添加附件:文件小于20M 文件格式必须为doc,docx,xls,xlsx,pdf,ppt,pptx,txt,zip,rar,tar,7z
上传
文件格式必须为doc,docx,xls,xlsx,pdf,ppt,pptx,txt,zip,rar,tar,7z
确定要删除此文章、专栏、评论吗?
确定
取消

关注公众号