rv1126-A/B升级方案报错

一、修改配置
打开device/rockchip/RV1126_RV1109/BoardConfig.mk，将RK_Uboot_DEFCONFIG配置成rv1126-ab；

二、修改分区参数
根据mkfirmware.sh文件中的参数PARAMETER，查到.BoardConfig.mk的参数RK_PARAMETER为parameter-buildroot-fit.txt，然后修改parameter-Buildroot-fit.txt中的参数，如下：

FIRMWARE_VER: 8.1
MACHINE_MODEL: RV1126
MACHINE_ID: 007
MANUFACTURER: RV1126
MAGIC: 0x5041524B
ATAG: 0x00200800
MACHINE: 0xffffffff
CHECK_MASK: 0x80
PWR_HLD: 0,0,A,0,1
TYPE: gpt
CMDLINE: mtdparts=rk29xxNAND:0x00002000@0x00004000(uboot),0x00002000@0x00006000(trust),0x00002000@0x00008000(misc),0x00008000@0x0000a000(boot_a),0x00008000@0x00012000(boot_b),0x000a0000@0x0001a000(system_a),0x000a0000@0x000ba000(system_b),0x00040000@0x0015a000(oem),0x00040000@0x0019a000(userdata),-@0x001da000(media:grow)
uuid:rootfs=614e0000-0000-4b53-8000-1d28000054a9

三、编译
重新编译制作(./build.sh all、./mkfirmware.sh)

四、烧写
1、打开烧写工具RKDevTool.exe，配置项及地址参数等如下所示（misc.img不进行烧写）：

2、按demo板的“Update”和“RESET”键进入MASKrom模式，然后点击“执行”进行烧写；
3、烧写完成后系统重启，进入到内核运行到一半停止，整个启动的打印信息如下：

DDR version V1.03 20200804
DDR3, 328MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB
change to: 328MHz
change to: 528MHz
change to: 784MHz
change to: 924MHz(final freq)
out
U-Boot SPL board init
U-Boot SPL 2017.09-g514da39-200804 #cjh (Aug 05 2020 - 16:04:04)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC1
## Verified-boot: 0
## Checking optee 0x08400000 ... sha256+ OK
## Checking uboot 0x00400000 ... sha256+ OK
## Checking fdt 0x004b54a4 ... sha256+ OK
Jumping to U-Boot(0x00400000) via OP-TEE(0x08400000)

I/TC:
I/TC: cpu feature:0x0
I/TC: cpu_st=0xe0
I/TC: OP-TEE version: 3.6.0-292-g3fa0dc8d #14 Fri Sep 18 02:55:54 UTC 2020 arm
I/TC: Next entry point address: 0x00400000
I/TC: Initialized


U-Boot 2017.09-g6ab927d-200914 #root (Oct 26 2020 - 23:34:06 -0700)

Model: Rockchip RV1126 Evaluation Board
PreSerial: 2
DRAM:&nBSP; 1021.7 MiB
Sysmem: init
Relocation Offset: 00000000, fdt: 3bcfa298
Using default environment

dwmmc@ffc50000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
boot mode: None
A/B-slot: _a, successful: 0, tries-remain: 7
DTB: rk-kernel.dtb
FIT: no signed, no conf required
HASH(c): OK
I2C0 speed: 400000Hz
PMIC:  RK8090 (on=0x14, off=0x00)
vdd_npu_vepu 800000 uV
vdd_arm 800000 uV
io-domain: OK
Can't get crtc id, default set to id = 0
Model: Rockchip RV1126 EVB DDR3 V13 Board
Rockchip UBOOT DRM driver version: v1.0.1
Using display timing dts
Detailed mode clock 65000 kHz, flags[a]
    H: 0720 0768 0776 0828
    V: 1280 1296 1302 1317
bus_format: 100e
final DSI-Link bandwidth: 480 Mbps x 4
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  apll 1008000 KHz
  dpll 462000 KHz
  gpll 1188000 KHz
  cpll 500000 KHz
  hpll 1400000 KHz
  aclk_pdbus 500000 KHz
  hclk_pdbus 198000 KHz
  pclk_pdbus 99000 KHz
  aclk_pdphp 297000 KHz
  hclk_pdphp 198000 KHz
  hclk_pdaudio 148500 KHz
  hclk_pdcore 198000 KHz
  pclk_pdpmu 99000 KHz
Net:   
Error: ethernet@ffc40000 address not set.
No ethernet found.
Hit key to stop autoboot('CTRL+C'):  0
## Booting FIT Image at 0x3b530680 with size 0x005c6c00
Fdt Ramdisk skip relocation
## LoADIng kernel from FIT Image at 3b530680 ...
   Using 'conf' configuration
optee api revision: 2.0
TEEC: Waring: Could not find security partition
## Verified-boot: 0
   Trying 'kernel' kernel subimage
     Description:  unavailable
     Type:         Kernel Image
     Compression:  uncompressed
     Data start:   0x3b548c80
     Data Size:    5957088 Bytes = 5.7 MiB
     Architecture: ARM
     OS:           linux
     Load Address: 0x02008000
     Entry Point:  0x02008000
     Hash algo:    sha256
     Hash value:   16ec64b09c0696a1ca55583a2cd339dd435e593530cbc857c64a54112d1ba42b
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at 3b530680 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  unavailable
     Type:         Flat Device tree
     Compression:  uncompressed
     Data Start:   0x3b530e80
     Data Size:    97710 Bytes = 95.4 KiB
     Architecture: ARM
     Load Address: 0x08300000
     Hash algo:    sha256
     Hash value:   591f2f6f282873e7df5b66a1e3ceedbde98b017d390bf3aebcc89c1d83c68551
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x08300000 to 0x08300000
   Booting using the fdt blob at 0x8300000
   Loading Kernel Image from 0x3b548c80 to 0x02008000 ... OK
  'reserved-memory' ramoops@8000000: addr=8000000 size=100000
   Using Device Tree in place at 08300000, end 0831adad
Adding bank: 0x00000000 - 0x08400000 (size: 0x08400000)
Adding bank: 0x08648000 - 0x40000000 (size: 0x379b8000)
Total: 1371.55 ms

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0xf00
[    0.000000] Linux version 4.19.111 (root@Ubuntu) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #1 SMP PREEMPT Mon Oct 19 00:19:55 PDT 2020
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Rockchip RV1126 EVB DDR3 V13 Board
[    0.000000] earlycon: UART8250 at MMIO32 0xff570000 (options '')
[    0.000000] bootconsole [uart8250] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x2dc00000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node isp, compatible id shared-dma-pool
[    0.000000] cma: Reserved 8 MiB at 0x3f800000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC calling Convention v1.0
[    0.000000] percpu: Embedded 15 pages/cpu s32140 r8192 d21108 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 259512
[    0.000000] Kernel command line: user_debug=31 storagemedia=EMMC androidboot.storagemedia=emmc androidboot.mode=normal  rootwait earlycon=uart8250,mmio32,0xff570000 console=ttyFIQ0 rootfstype=ext4 snd_aloop.index=7
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 750540K/1046240K available (8192K kernel code, 329K rwdata, 1876K rodata, 1024K init, 893K bss, 25364K reserved, 270336K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xfffF1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
[    0.000000]     lowmem  : 0xb0000000 - 0xf0000000   (1024 MB)
[    0.000000]     pkmap   : 0xafe00000 - 0xb0000000   (   2 MB)
[    0.000000]     modules : 0xaf000000 - 0xafe00000   (  14 MB)
[    0.000000]       .text : 0x(ptrval) - 0x(ptrval)   (9184 kB)
[    0.000000]       .init : 0x(ptrval) - 0x(ptrval)   (1024 kB)
[    0.000000]       .data : 0x(ptrval) - 0x(ptrval)   ( 330 kB)
[    0.000000]        .bss : 0x(ptrval) - 0x(ptrval)   ( 894 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]         Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: random: get_random_bytes called from start_kernel+0x324/0x4a4 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000759] Switching to timer-based delay loop, resolution 41ns
[    0.002631] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.003595] pid_max: default: 4096 minimum: 301
[    0.004208] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.004837] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.006182] CPU: Testing write buffer coherency: ok
[    0.006993] /cpus/cpu@f00 missing clock-frequency property
[    0.007519] /cpus/cpu@f01 missing clock-frequency property
[    0.008040] /cpus/cpu@f02 missing clock-frequency property
[    0.008562] /cpus/cpu@f03 missing clock-frequency property
[    0.009078] CPU0: thread -1, cpu 0, SOCket.html" target="_blank" class="relatedlink">Socket 15, mpidr 80000f00
[    0.010363] Setting up static identity map for 0x100000 - 0x100060
[    0.011106] rcu: Hierarchical SRCU implementation.
[    0.012184] smp: Bringing up secondary CPUs ...
[    0.013532] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[    0.014531] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[    0.015460] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[    0.015591] smp: Brought up 1 node, 4 CPUs
[    0.017644] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[    0.018226] CPU: All CPU(s) started in SVC mode.
[    0.019496] devtmpfs: initialized
[    0.045185] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.046535] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.047515] futex hash table entries: 16 (order: -2, 1024 bytes)
[    0.059714] pinctrl core: initialized pinctrl subsystem
[    0.061558] NET: Registered protocol family 16
[    0.063893] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.066419] cpuidle: using governor menu
[    0.066812] Registered FIQ tty driver
[    0.067632] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.068422] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.071351] console [pstore-1] enabled
[    0.072012] pstore: Registered ramoops as persistent store backend
[    0.072596] ramoops: attached 0x100000@0x8000000, ecc: 0/0
[    0.118055] cryptd: max_cpu_qlen set to 1000
[    0.119327] fiq debugger fiq mode enabled
[[    0.120130] console [ttyFIQ0] enabled
    0.120130] console [ttyFIQ0] enabled
[    0.120849] bootconsole [uart8250] disabled
[    0.120849] bootconsole [uart8250] disabled
[    0.121533] Registered fiq debugger ttyFIQ0
[    0.122149] rockchip-pm rockchip-suspend: not set PWM-regulator-config
[    0.125196] rk_iommu ffb00f00.iommu: version = 1
[    0.125797] rk_iommu ffb20800.iommu: version = 1
[    0.126247] rk_iommu ffb60e00.iommu: version = 1
[    0.126885] rk_iommu ffb80480.iommu: version = 1
[    0.127443] rk_iommu ffb90800.iommu: version = 1
[    0.127971] rk_iommu ffbb0f00.iommu: version = 1
[    0.128958] SCSI subsystem initialized
[    0.129268] usbcore: registered new interface driver usbfs
[    0.129364] usbcore: registered new interface driver hub
[    0.129536] usbcore: registered new device driver usb
[    0.129644] media: Linux media interface: v0.10
[    0.129721] videodev: Linux video capture interface: v2.00
[    0.129797] pps_core: LinuxPPS API ver. 1 registered
[    0.129821] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.129865] PTP clock support registered
[    0.131280] Advanced Linux Sound Architecture Driver Initialized.
[    0.131951] Bluetooth: Core ver 2.22
[    0.132036] NET: Registered protocol family 31
[    0.132062] Bluetooth: HCI device and connection manager initialized
[    0.132093] Bluetooth: HCI socket layer initialized
[    0.132122] Bluetooth: L2CAP socket layer initialized
[    0.132182] Bluetooth: SCO socket layer initialized
[    0.132668] rockchip-cpuinfo cpuinfo: SoC                : 11260000
[    0.132704] rockchip-cpuinfo cpuinfo: Serial                : 0000000000000000
[    0.133620] clocksource: Switched to clocksource arch_sys_counter
[    0.136219] NET: Registered protocol family 2
[    0.137123] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[    0.137185] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.137334] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.137540] TCP: Hash tables configured (established 8192 bind 8192)
[    0.137703] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.137775] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.138009] NET: Registered protocol family 1
[    0.139726] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.142324] Initialise system trusted keyrings
[    0.142571] workingset: timestamp_bits=29 max_order=18 bucket_order=0
[    0.149921] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.152760] Key type asymmetric registered
[    0.152792] Asymmetric key parser 'x509' registered
[    0.152861] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    0.152890] io scheduler noop registered
[    0.152912] io scheduler deadline registered
[    0.153090] io scheduler cfq registered (default)
[    0.153118] io scheduler mq-deadline registered
[    0.153141] io scheduler kyber registered
[    0.153300] io scheduler bfq registered
[    0.157419] phy phy-ff4c0000.usb2-phy.1: Failed to get VBUS supply regulator
[    0.159369] rockchip-usb2phy-naneng ff4c8000.usb2-phy: failed to create phy
[    0.161012] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    0.161137] pwm-backlight backlight: Linked as a consumer to regulator.0
[    0.161534] mpp_service mpp-srv: probe start
[    0.162402] iommu: Adding device ffb80000.rkvdec to group 3
[    0.162459] mpp_rkvdec ffb80000.rkvdec: Linked as a consumer to ffb80480.iommu
[    0.162652] mpp_rkvdec ffb80000.rkvdec: probing start
[    0.163296] mpp_rkvdec ffb80000.rkvdec: shared_niu_a is not found!
[    0.163326] rkvdec_init:1182: No niu aclk reset resource define
[    0.163361] mpp_rkvdec ffb80000.rkvdec: shared_niu_h is not found!
[    0.163386] rkvdec_init:1185: No niu hclk reset resource define
[    0.163793] mpp_rkvdec ffb80000.rkvdec: probing finish
[    0.164456] iommu: Adding device ffbb0000.rkvenc to group 5
[    0.164518] mpp_rkvenc ffbb0000.rkvenc: Linked as a consumer to ffbb0f00.iommu
[    0.164798] mpp_rkvenc ffbb0000.rkvenc: probing start
[    0.165377] mpp_rkvenc ffbb0000.rkvenc: venc regulator not ready, retry
[    0.165411] rkvenc_init:921: failed to add venc devfreq
[    0.166302] iommu: Adding device ffb90400.vdpu to group 4
[    0.166363] mpp_vdpu2 ffb90400.vdpu: Linked as a consumer to ffb90800.iommu
[    0.166471] mpp_vdpu2 ffb90400.vdpu: probe device
[    0.167051] mpp_vdpu2 ffb90400.vdpu: reset_group->rw_sem_on=0
[    0.167101] mpp_vdpu2 ffb90400.vdpu: reset_group->rw_sem_on=0
[    0.167344] mpp_vdpu2 ffb90400.vdpu: probing finish
[    0.167973] iommu: Adding device ffb90000.vepu to group 4
[    0.168020] mpp_vepu2 ffb90000.vepu: Linked as a consumer to ffb90800.iommu
[    0.168144] mpp_vepu2 ffb90000.vepu: probe device
[    0.168641] mpp_vepu2 ffb90000.vepu: reset_group->rw_sem_on=0
[    0.168682] mpp_vepu2 ffb90000.vepu: reset_group->rw_sem_on=0
[    0.168909] mpp_vepu2 ffb90000.vepu: probing finish
[    0.169431] iommu: Adding device ffb20000.iep to group 1
[    0.169487] mpp-iep2 ffb20000.iep: Linked as a consumer to ffb20800.iommu
[    0.169602] mpp-iep2 ffb20000.iep: probe device
[    0.170256] mpp-iep2 ffb20000.iep: allocate roi buffer failed
[    0.170519] mpp-iep2 ffb20000.iep: probing finish
[    0.170789] mpp_service mpp-srv: probe success
[    0.176235] dma-pl330 ff4e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.176279] dma-pl330 ff4e0000.dma-controller:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    0.178612] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    0.179478] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    0.180425] ff560000.serial: ttyS0 at MMIO 0xff560000 (irq = 32, base_baud = 1500000) is a 16550A
[    0.183049] random: fast init done
[    0.183549] iommu: Adding device ffb00000.vop to group 0
[    0.183574] random: crng init done
[    0.183639] rockchip-vop ffb00000.vop: Linked as a consumer to ffb00f00.iommu
[    0.187680] rockchip-drm display-subsystem: Linked as a consumer to ffb00000.vop
[    0.188714] rockchip-drm display-subsystem: Linked as a consumer to ffb30000.dsi
[    0.189970] rockchip-drm display-subsystem: devfreq is not set
[    0.190490] rockchip-drm display-subsystem: bound ffb00000.vop (ops 0xb093b9c0)
[    0.190563] dw-mipi-dsi ffb30000.dsi: [drm:dw_mipi_dsi_bind] *ERROR* Failed to find panel or bridge: -517
[    0.190601] rockchip-drm display-subsystem: failed to bind ffb30000.dsi (ops 0xb09420ec): -517
[    0.190869] rockchip-drm display-subsystem: master bind failed: -517
[    0.195720] panel-SIMple-dsi ffb30000.dsi.0: Linked as a consumer to regulator.1
[    0.195783] panel-simple-dsi ffb30000.dsi.0: ffb30000.dsi.0 supply vsp not found, using dummy regulator
[    0.195878] panel-simple-dsi ffb30000.dsi.0: Linked as a consumer to regulator.0
[    0.195924] panel-simple-dsi ffb30000.dsi.0: ffb30000.dsi.0 supply vsn not found, using dummy regulator
[    0.197357] zram: Added device: zram0
[    0.199248] libphy: Fixed MDIO Bus: probed
[    0.201140] rk_gmac-dwmac ffc40000.ethernet: no regulator found
[    0.201183] rk_gmac-dwmac ffc40000.ethernet: clock input or output? (input).
[    0.201207] rk_gmac-dwmac ffc40000.ethernet: TX delay(0x2a).
[    0.201237] rk_gmac-dwmac ffc40000.ethernet: RX delay(0x1a).
[    0.201267] rk_gmac-dwmac ffc40000.ethernet: integrated PHY? (no).
[    0.201355] rk_gmac-dwmac ffc40000.ethernet: clock input from PHY
[    0.206402] rk_gmac-dwmac ffc40000.ethernet: init for RGMII
[    0.206672] rk_gmac-dwmac ffc40000.ethernet: User ID: 0X30, Synopsys ID: 0x51
[    0.206699] rk_gmac-dwmac ffc40000.ethernet:         DWMAC4/5
[    0.206728] rk_gmac-dwmac ffc40000.ethernet: DMA HW capability register supported
[    0.206754] rk_gmac-dwmac ffc40000.ethernet: RX Checksum Offload Engine supported
[    0.206779] rk_gmac-dwmac ffc40000.ethernet: TX Checksum insertion supported
[    0.206803] rk_gmac-dwmac ffc40000.ethernet: Wake-Up On Lan supported
[    0.206871] rk_gmac-dwmac ffc40000.ethernet: TSO supported
[    0.206897] rk_gmac-dwmac ffc40000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    0.206924] rk_gmac-dwmac ffc40000.ethernet: TSO feature enabled
[    0.340334] libphy: stmmac: probed
[    0.343893] dwc3 ffd00000.dwc3: Failed to get clk 'ref': -2
[    0.349535] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.349574] ehci-platform: EHCI generic platform driver
[    0.350202] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.350255] ohci-platform: OHCI generic platform driver
[    0.351738] usbcore: registered new interface driver usb-storage
[    0.352484] i2c /dev entries driver
[    0.354417] RK808 0-0020: chip id: 0x8090
[    0.354525] rk808 0-0020: No cache defaults, reading back from HW
[    0.360942] rk808 0-0020: source: on=0x14, off=0x00
[    0.360982] rk808 0-0020: support dcdc3 fb mode:-22, -1331383588
[    0.361132] rk808 0-0020: support PMIC reset mode:0,0
[    0.365380] rk808-regulator rk808-regulator: there is no dvs0 GPIO
[    0.365505] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    0.365610] DCDC_REG1: supplied by vcc5v0_sys
[    0.366305] DCDC_REG2: supplied by vcc5v0_sys
[    0.366921] DCDC_REG3: supplied by vcc5v0_sys
[    0.367481] DCDC_REG4: supplied by vcc5v0_sys
[    0.367975] DCDC_REG5: supplied by vcc5v0_sys
[    0.368561] LDO_REG1: supplied by vcc_buck5
[    0.369168] LDO_REG2: supplied by vcc_buck5
[    0.369640] LDO_REG3: supplied by vcc_buck5
[    0.370131] LDO_REG4: supplied by vcc_buck5
[    0.370676] LDO_REG5: supplied by vcc_buck5
[    0.371126] LDO_REG6: supplied by vcc_buck5
[    0.371227] vcc_dvdd: Bringing 1100000uV into 1200000-1200000uV
[    0.371785] LDO_REG7: supplied by vcc5v0_sys
[    0.372265] LDO_REG8: supplied by vcc5v0_sys
[    0.372894] LDO_REG9: supplied by vcc5v0_sys
[    0.373501] SWITCH_REG1: supplied by vcc5v0_sys
[    0.373988] SWITCH_REG2: supplied by vcc3v3_sys
[    0.376203] input: RK805 pwrkey as /devices/platform/ff3f0000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0
[    0.379224] rk808-rtc rk808-rtc: registered as rtc0
[    0.379828] rk808-rtc rk808-rtc: setting system clock to 2017-08-05 09:55:48 UTC (1501926948)
[    0.381875] i2c i2c-1: 1 i2c clients have been registered at 0x36
[    0.383085] <<GTP-INF>>[gt1x_ts_probe:537] GTP Driver Version: V1.4<2015/07/10>
[    0.383123] <<GTP-INF>>[gt1x_ts_probe:538] GTP I2C Address: 0x14
[    0.383265] <<GTP-ERR>>[gt1x_parse_dt:334] vdd_ana not SPECified, fallback to power-supply
[    0.383408] Goodix-TS-GT1X 5-0014: Linked as a consumer to regulator.1
[    0.383564] <<GTP-INF>>[gt1x_reset_GUItar:784] GTP RESET!
[    0.383849] ircut cam_ircut: driver version: 00.01.00
[    0.384120] ircut cam_ircut: failed get pulse-width,use dafult value 100
[    0.384416] ircut cam_ircut: Failed to get led-gpIOS
[    0.384457] ircut cam_ircut: probe successful!
[    0.384995] ERROR: could not get clock /mipi-csi2@ffb10000:srst_csihost_p(1)
[    0.385027] rockchip-mipi-csi2: failed to get rst clock, maybe useless
[    0.385289] rockchip-mipi-csi2: probe success, v4l2_dev:(null)!
[    0.386536] rkcifhw ffae0000.rkcif: no iommu attached, using non-iommu buffers
[    0.386576] rkcifhw ffae0000.rkcif: assigned reserved memory node isp
[    0.386726] rkcif rkcif_dvp: rkcif driver version: v00.01.08
[    0.386837] rkcif rkcif_dvp: attach to cif hw node
[    0.386868] rkcif rkcif_dvp: no iommu attached, using non-iommu buffers
[    0.386905] rkcif rkcif_dvp: assigned reserved memory node isp
[    0.387439] rkcif_dvp: Failed to register subdev notifier(-19)
[    0.387897] rkcif rkcif_dvp: detach to cif hw node
[    0.388012] rkcif rkcif_mipi_LVDS: rkcif driver version: v00.01.08
[    0.388121] rkcif rkcif_mipi_lvds: attach to cif hw node
[    0.388151] rkcif rkcif_mipi_lvds: no iommu attached, using non-iommu buffers
[    0.388188] rkcif rkcif_mipi_lvds: assigned reserved memory node isp
[    0.389209] rkcif rkcif_mipi_lvds: Entity type for entity rockchip-mipi-csi2 was not initialized!
[    0.391450] rkisp_hw ffb50000.rkisp: is_thunderboot: 0
[    0.391491] rkisp_hw ffb50000.rkisp: Missing rockchip,grf property
[    0.391809] rkisp_hw ffb50000.rkisp: no iommu attached, using non-iommu buffers
[    0.391853] rkisp_hw ffb50000.rkisp: assigned reserved memory node isp
[    0.392112] rkisp rkisp-vir0: rkisp driver version: v00.01.07
[    0.392349] rkisp rkisp-vir0: No memory-region-thunderboot specified
[    0.392590] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[    0.392633] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized!
[    0.392666] rkisp rkisp-vir0: Entity type for entity rkisp-bridge-ispp was not initialized!
[    0.400008] iommu: Adding device ffb60000.rkispp to group 2
[    0.400064] rkispp_hw ffb60000.rkispp: Linked as a consumer to ffb60e00.iommu
[    0.400710] rkispp_hw ffb60000.rkispp: max input:0x0@0fps
[    0.400763] rkispp_hw ffb60000.rkispp: can't request region for resource [mem 0xffb60000-0xffb7ffff]
[    0.401263] rkispp rkispp-vir0: rkispp driver version: v00.01.07
[    0.404263] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.16
[    0.404391] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.12
[    0.404602] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.19
[    0.404870] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.10
[    0.404979] rockchip-iodomain fe020000.syscon:io-domains: Linked as a consumer to regulator.7
[    0.407658] rockchip-thermal ff5f0000.tsADC: tsadc trimmed value = 13
[    0.408010] rockchip-thermal ff5f0000.tsadc: tsadc is probed successfully!
[    0.408470] rockchip-thermal ff5f8000.tsadc: tsadc trimmed value = 14
[    0.408725] rockchip-thermal ff5f8000.tsadc: tsadc is probed successfully!
[    0.409628] Bluetooth: HCI UART driver ver 2.3
[    0.409660] Bluetooth: HCI UART protocol H4 registered
[    0.409972] cpu cpu0: Failed to get leakage
[    0.410133] cpu cpu0: Linked as a consumer to regulator.5
[    0.410168] cpu cpu0: Failed to get pvtm
[    0.410263] cpu cpu0: Dropping the link to regulator.5
[    0.410693] cpu cpu0: Linked as a consumer to regulator.5
[    0.410780] cpu cpu0: Dropping the link to regulator.5
[    0.411010] cpu cpu0: Linked as a consumer to regulator.5
[    0.412111] cpu cpu0: avs=0
[    0.412554] cpu cpu0: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[    0.412589] cpu cpu0: failed to read out thermal zone (-22)
[    0.413495] cpu cpu0: failed to find power_model node
[    0.413642] cpuidle: enable-method property 'psci' found operations
[    0.413745] cpuidle: enable-method property 'psci' found operations
[    0.413819] cpuidle: enable-method property 'psci' found operations
[    0.413886] cpuidle: enable-method property 'psci' found operations
[    0.414462] Synopsys Designware Multimedia Card Interface Driver
[    0.414924] dwmmc_rockchip ffc50000.dwmmc: IDMAC supports 32-bit address mode.
[    0.415034] dwmmc_rockchip ffc50000.dwmmc: Using internal DMA controller.
[    0.415050] dwmmc_rockchip ffc50000.dwmmc: Version ID is 270a
[    0.415102] dwmmc_rockchip ffc50000.dwmmc: DW MMC controller at irq 62,32 bit host data width,256 deep fifo
[    0.415213] mmc_host mmc0: card is non-removable.
[    0.427293] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    0.441794] dwmmc_rockchip ffc60000.dwmmc: IDMAC supports 32-bit address mode.
[    0.442950] dwmmc_rockchip ffc60000.dwmmc: Using internal DMA controller.
[    0.443023] dwmmc_rockchip ffc60000.dwmmc: Version ID is 270a
[    0.443232] dwmmc_rockchip ffc60000.dwmmc: DW MMC controller at irq 63,32 bit host data width,256 deep fifo
[    0.443547] dwmmc_rockchip ffc60000.dwmmc: Linked as a consumer to regulator.16
[    0.454552] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    0.454604] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[    0.454625] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[    0.457096] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    0.471227] dwmmc_rockchip ffc70000.dwmmc: IDMAC supports 32-bit address mode.
[    0.471538] dwmmc_rockchip ffc70000.dwmmc: Using internal DMA controller.
[    0.471611] dwmmc_rockchip ffc70000.dwmmc: Version ID is 270a
[    0.471768] dwmmc_rockchip ffc70000.dwmmc: DW MMC controller at irq 64,32 bit host data width,256 deep fifo
[    0.472143] dwmmc_rockchip ffc70000.dwmmc: allocated mmc-pwrseq
[    0.472191] mmc_host mmc2: card is non-removable.
[    0.480238] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 200000000Hz, actual 198000000HZ div = 0)
[    0.480356] dwmmc_rockchip ffc50000.dwmmc: Successfully tuned phase to 90
[    0.483892] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    0.484071] mmc0: new HS200 MMC card at address 0001
[    0.486676] mmcblk0: mmc0:0001 AJTD4R 14.6 GiB
[    0.488072] mmcblk0boot0: mmc0:0001 AJTD4R partition 1 4.00 MiB
[    0.489366] mmcblk0boot1: mmc0:0001 AJTD4R partition 2 4.00 MiB
[    0.489806] mmcblk0rpmb: mmc0:0001 AJTD4R partition 3 4.00 MiB, chardev (242:0)
[    0.497629] usbcore: registered new interface driver usbhid
[    0.497683] usbhid: USB HID core driver
[    0.499553] rockchip-saradc ff5e0000.saradc: Linked as a consumer to regulator.12
[    0.500570] rkSFC_base v1.1 2016-01-08
[    0.501130] rksfc ffc90000.sfc: rksfc_probe clk rate = 79200000
[    0.501247] rkflash_dev_init enter
[    0.501285] sfc nor id: 0 0 0
[    0.501318] rkflash[1] is invalid
[    0.501323] rkflash_dev_init enter
[    0.501349] sfc_nand id: 0 0 0
[    0.501365] rkflash[2] is invalid
[    0.502858]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 P10
[    0.508303] RK817-codec rk817-codec: DMA mask not set
[    0.512372] NET: Registered protocol family 17
[    0.512452] NET: Registered protocol family 15
[    0.512820] Bluetooth: RFCOMM TTY layer initialized
[    0.512872] Bluetooth: RFCOMM socket layer initialized
[    0.512912] Bluetooth: RFCOMM ver 1.11
[    0.512935] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    0.512955] Bluetooth: HIDP socket layer initialized
[    0.512969] [BT_RFKILL]: Enter rfkill_rk_init
[    0.512981] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    0.513380] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    0.513405] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = AP6255
[    0.513419] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    0.513430] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power contrOLED by gpio.
[    0.513501] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 8, flags = 0.
[    0.513538] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    0.513554] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    0.514159] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 48.
[    0.514215] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 7.
[    0.514271] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 5.
[    0.514291] [BT_RFKILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.
[    0.514368] [BT_RFKILL]: Request irq for bt wakeup host
[    0.514493] [BT_RFKILL]: ** disable irq
[    0.514660] [BT_RFKILL]: bt_default device registered.
[    0.515315] flash vendor_init_thread!
[    0.515391] flash vendor storage:20170308 ret = -1
[    0.515561] os04a10 1-0036-1: driver version: 00.01.03
[    0.515599] os04a10 1-0036-1:  Get hdr mode failed! no hdr default
[    0.515866] os04a10 1-0036-1: could not get sleep pinstate
[    0.516012] os04a10 1-0036-1: Linked as a consumer to regulator.15
[    0.516148] os04a10 1-0036-1: Linked as a consumer to regulator.13
[    0.516255] os04a10 1-0036-1: Linked as a consumer to regulator.14
[    0.516466] clk_mipicsi_out2io_fracdiv p_rate(297000000) is low than rate(24000000)*20, use integer or half-div
[    0.516764] vendor storage:20190527 ret = 0
[    0.528051] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    0.528061] os04a10 1-0036-1: Unexpected sensor id(000000), ret(-5)
[    0.528101] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[    0.528126] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[    0.528224] os04a10 1-0036-1: Dropping the link to regulator.15
[    0.528367] os04a10 1-0036-1: Dropping the link to regulator.13
[    0.528469] os04a10 1-0036-1: Dropping the link to regulator.14
[    0.528805] OV4689 1-0036: driver version: 00.01.06
[    0.528970] ov4689 1-0036: Failed to get pwdn-gpios
[    0.529037] ov4689 1-0036: could not get sleep pinstate
[    0.529140] ov4689 1-0036: Linked as a consumer to regulator.15
[    0.529231] ov4689 1-0036: Linked as a consumer to regulator.13
[    0.529310] ov4689 1-0036: Linked as a consumer to regulator.14
[    0.529407] clk_mipicsi_out2io_fracdiv p_rate(297000000) is low than rate(24000000)*20, use integer or half-div
[    0.531100] ov4689 1-0036: Unexpected sensor id(000000), ret(-5)
[    0.531277] ov4689 1-0036: Dropping the link to regulator.15
[    0.531360] ov4689 1-0036: Dropping the link to regulator.13
[    0.531432] ov4689 1-0036: Dropping the link to regulator.14
[    0.531922] Registering SWP/SWPB emulation handler
[    0.533075] Loading compiled-in X.509 certificates
[    0.535172] rga2: Driver loaded successfully ver:3.02
[    0.535532] rga2: Module initialized.
[    0.542489] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[    0.544158] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    0.545785] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[    0.548670] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
[    0.552118] mmc2: queuing unknown CIS tuple 0x81 (9 bytes)
[    0.560232] phy phy-ff4c8000.usb2-phy.2: Linked as a consumer to regulator.18
[    0.563106] mpp_rkvenc ffbb0000.rkvenc: probing start
[    0.564010] mpp_rkvenc ffbb0000.rkvenc: Linked as a consumer to regulator.4
[    0.564062] mpp_rkvenc ffbb0000.rkvenc: Failed to get leakage
[    0.564138] mpp_rkvenc ffbb0000.rkvenc: Failed to get pvtm
[    0.564643] mpp_rkvenc ffbb0000.rkvenc: avs=0
[    0.564988] mpp_rkvenc ffbb0000.rkvenc: failed to find power_model node
[    0.565018] mpp_rkvenc ffbb0000.rkvenc: failed to initialize power model
[    0.565227] mpp_rkvenc ffbb0000.rkvenc: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[    0.565279] mpp_rkvenc ffbb0000.rkvenc: failed to read out thermal zone (-22)
[    0.566028] mpp_rkvenc ffbb0000.rkvenc: probing finish
[    0.568612] rockchip-drm display-subsystem: devfreq is not set
[    0.569053] rockchip-drm display-subsystem: bound ffb00000.vop (ops 0xb093b9c0)
[    0.569116] rockchip-drm display-subsystem: bound ffb30000.dsi (ops 0xb09420ec)
[    0.569136] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    0.569146] [drm] No driver support for vblank timestamp query.
[    0.577444] [drm] Initialized rockchip 2.0.0 20140818 for display-subsystem on minor 0
[    0.581904] ehci-platform ffe00000.usb: EHCI Host Controller
[    0.582024] ehci-platform ffe00000.usb: new USB bus registered, assigned bus number 1
[    0.582467] ehci-platform ffe00000.usb: irq 67, io mem 0xffe00000
[    0.597043] ehci-platform ffe00000.usb: USB 2.0 started, EHCI 1.00
[    0.597473] usb usb1: New USB device found, idVendor=1d6b, idproduct=0002, bcdDevice= 4.19
[    0.597558] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.597587] usb usb1: Product: EHCI Host Controller
[    0.597615] usb usb1: Manufacturer: Linux 4.19.111 ehci_hcd
[    0.597641] usb usb1: SerialNumber: ffe00000.usb
[    0.599264] hub 1-0:1.0: USB hub found
[    0.599360] hub 1-0:1.0: 1 port detected
[    0.600427] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    0.600456] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[    0.600486] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[    0.600629] ohci-platform ffe10000.usb: Generic Platform OHCI controller
[    0.600779] ohci-platform ffe10000.usb: new USB bus registered, assigned bus number 2
[    0.601273] ohci-platform ffe10000.usb: irq 68, io mem 0xffe10000
[    0.629593] mmc_host mmc2: Bus speed (slot 0) = 198000000Hz (slot req 200000000Hz, actual 198000000HZ div = 0)
[    0.661280] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[    0.661323] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.661339] usb usb2: Product: Generic Platform OHCI controller
[    0.661354] usb usb2: Manufacturer: Linux 4.19.111 ohci_hcd
[    0.661368] usb usb2: SerialNumber: ffe10000.usb
[    0.662351] hub 2-0:1.0: USB hub found
[    0.662421] hub 2-0:1.0: 1 port detected
[    0.663360] input: adc-keys as /devices/platform/adc-keys/input/input1
[    0.667844] asoc-simple-card rk809-sound: rk817-HIFI <-> ff800000.I2S mapping ok
[    0.667898] asoc-simple-card rk809-sound: ASoC: no source widget found for MICBIAS1
[    0.667911] asoc-simple-card rk809-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack
[    0.667922] asoc-simple-card rk809-sound: ASoC: no sink widget found for IN1P
[    0.667932] asoc-simple-card rk809-sound: ASoC: Failed to add route Mic Jack -> direct -> IN1P
[    0.667943] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOL
[    0.667953] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOL -> direct -> Headphone Jack
[    0.667963] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOR
[    0.667975] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOR -> direct -> Headphone Jack
[    0.670548] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    0.670804] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    0.670836] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[    0.670851] <<GTP-INF>>[gt1x_reset_guitar:784] GTP RESET!
[    0.674402] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    0.674836] rkcif rkcif_mipi_lvds: clear unready subdev num: 1
[    0.675196] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    0.675214] cfg80211: failed to load regulatory.db
[    0.675623] rkcif_mipi_lvds: Async subdev notifier completed
[    0.675671] rkisp rkisp-vir0: clear unready subdev num: 1
[    0.677633] rockchip-mipi-dphy-rx: No link between dphy and sensor
[    0.677669] rkisp0: update sensor failed
[    0.677768] ALSA device list:
[    0.677786]   #0: rockchip,rk809-codec
[    0.677802]   #7: Loopback 1
[    0.741377] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    0.741450] <<GTP-ERR>>[gt1x_init:2315] Reset guitar failed!
[    0.741475] <<GTP-ERR>>[gt1x_init:2341] Init failed, use default setting
[    0.741582] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-6)
[    0.741622] <<GTP-ERR>>[gt1x_get_chip_type:891] I2c communication error.
[    0.741656] <<GTP-ERR>>[gt1x_init:2351] Get chip type failed!
[    0.742417] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-6)
[    0.742478] <<GTP-ERR>>[gt1x_read_version:841] Read version failed!
[    0.751078] dwmmc_rockchip ffc70000.dwmmc: Successfully tuned phase to 231
[    0.760267] mmc2: new ultra high speed SDR104 SDIO card at address 0001
[    0.847455] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-6)
[    0.847527] <<GTP-ERR>>[gt1x_read_version:841] Read version failed!
[    0.955139] <<GTP-ERR>>[_do_i2c_read:388] I2c Transfer error! (-6)
[    0.955225] <<GTP-ERR>>[gt1x_read_version:841] Read version failed!
[    1.060656] <<GTP-INF>>[gt1x_read_version:859] IC VERSION:GT_000000(Patch)_0000(Mask)_00(SensorID)
[    1.060726] <<GTP-INF>>[gt1x_init_panel:604] Config group0 used, length:239
[    1.060758] <<GTP-INF>>[gt1x_init_panel:655] X_MAX=4096,Y_MAX=4096,TRIGGER=0x01,WAKEUP_LEVEL=1
[    1.060932] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    1.061674] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    1.062460] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    1.063243] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    1.064010] <<GTP-ERR>>[_do_i2c_write:430] I2c transfer error! (-6)
[    1.064079] <<GTP-ERR>>[gt1x_send_cfg:549] Send config failed!
[    1.064123] <<GTP-ERR>>[gt1x_init:2363] Init panel failed.
[    1.065356] <<GTP-ERR>>[gt1x_ts_probe:564] GTP init failed!!!
[    1.065546] Goodix-TS-GT1X 5-0014: Dropping the link to regulator.1
[    1.065673] Goodix-TS-GT1X: probe of 5-0014 failed with error -2147483644
[    1.066182] Waiting for root device ...
[    1.573951] phy phy-ff4c0000.usb2-phy.1: charger = USB_SDP_CHARGER

请问各位大侠，为什么卡在这里了呢？请指教，非常感谢！