ulockn

ulockn

0个粉丝

3

问答

0

专栏

0

资料

ulockn  发布于  2025-09-18 14:52:07
采纳率 0%
3个问答
307

ws73wifi在3516cv610上加载驱动,有遇到这种问题吗,如何解决,在73wifi驱动中没有-1这个错误码

 

/ # ./wifi_sta.sh start
The file exists
plat_soc: loading out-of-tree module taints kernel.
plat_soc:W]ini_file_name@/etc/ws73/ws73_cfg.ini
plat_soc:EMERG]0:emerg log.
plat_soc:ALERT]1:alert log.
plat_soc:CRIT]2:crit log.
plat_soc:E]3:err log.
plat_soc:W]4:warning log.
plat_soc:E]custom ini[plat kern log level]: 7.
plat_soc:E]board_power_gpio_init::succ, power_gpio_idx=[40]!
plat_soc:E]board_wakeup_gpio_init::succ, wkup_gpio_idx=[70]!
[USB][I]OFF —> INIT
[usb_set_bus_state:87]
[USB][I]boot usb[oal_usb_probe:1424]
[USB][I]bulk_in_ep:0x81[oal_usb_boot_bulk_in_probe:1324]
[USB][I]dev->bulk_out_ep:0x1[oal_usb_boot_bulk_out_probe:1355]
[USB][I]INIT —> BOOT
[usb_set_bus_state:87]
[USB][I]usb boot probe success[oal_usb_boot_init_config:1398]
usbcore: registered new interface driver wireless_usb
plat_soc:E]hcc diag log service ini ok
plat_soc:W]plat_misc_init!
plat_soc:W]plat_init_etc::succ!

insmod wifi ko beginning!
[FRW] frw_timer_init enter
frw_start_hcc_service type:6, ret=0
frw_start_hcc_service type:4, ret=0
[FRW] frw_main_init_etc end
hwifi_custom_host_read_cfg_init finish!
hwifi_cfg_host_global_init_param: rx_stbc[1] ret[0]
hwifi_cfg_tcp_ack_param_init: tcp_ack_filter_enable[1] ret[0]
hwifi_cfg_tcp_ack_param_init: tcp_ack_max_num_start_process[2] ret[0]
hwifi_cfg_host_global_init_param: user num[8] ret[0]
hwifi_cfg_scan_para_cfg_init probe send times, ret 0 priv_value 2
get scan time, ret 0 priv_value 30
get scan count, ret 0 priv_value 2
hwifi_cfg_scan_probe_ie_cfg_init ret 0 priv_value 1
hwifi_cfg_scan_probe_del_wps_ie_cfg_init ret 0 priv_value 1
g_scan_probe_req_del_wps_ie = 1
hwifi_cfg_random_mac_addr_scan_init ret 0 priv_value 1
hwifi_cfg_random_mac_addr_scan_oui_init ret 65535 priv_value 0
hwifi_cfg_pcap_file_len_max_cfg_init ret 0 priv_value 12
hwifi_cfg_data_sample_param_init: data_sample[0] ret[0]
hwifi_cfg_host_global_init_param: apf enable[1] ret[0]
hwifi_cfg_host_global_init_param: 11ax protocol enable[0] ret[0]
hwifi_cfg_host_global_init_param: wow_event[15] ret[0]
hwifi_cfg_host_global_init_param: wow_enable[1] ret[0]
hwifi_cfg_host_global_init_param: smooth_phase_en[1] ret[0]
hwifi_cfg_host_global_init_param: over_ds_en[1] ret[0]
{wal_set_wlan_name_config::g_wlan_name[0]=wlan0}
{wal_set_wlan_name_config::g_wlan_name[1]=wlan1}
{wal_set_wlan_name_config::g_wlan_name[2]=p2p0}
dfx_user_rd_init success!
hmac_register_pm_callback_etc:wlan_pm_get_wifi_srv_handler_etc is null
plat_soc:E]pm_svc_open::first svc open, pm_svc_power_on!
plat_soc:E]firmware_download_etc begin
plat_soc:E][/etc/ws73/ws73.bin] sha256sum check succ!!
plat_soc:E][/etc/ws73/wifi_cali.bin] sha256sum check succ!!
plat_soc:E][/etc/ws73/btc_cali.bin] sha256sum check succ!!
usb 1-1: USB disconnect, device number 2
[USB][I]usb disconnect
[oal_usb_disconnect:1584]
[USB][I]BOOT —> DISCONNECT
[usb_set_bus_state:87]
usb 1-1: new high-speed USB device number 3 using xhci-hcd
[USB][I]kernel usb[oal_usb_probe:1419]
[USB][I]7 5 81 2 200 0[oal_usb_system_init_bulk_ep:945]
[USB][I]EP bulk_in:129, bulk_out:1, int_in:131[oal_usb_system_ep_init:1046]
[USB][I]rw reg ep_in:[130], ep_out:[2][oal_usb_init_rw_reg_ep:928]
[USB][I]start[usb_transfer_rx_data_handle:795]
[USB][I]DISCONNECT —> WORK
[usb_set_bus_state:87]
[USB][I]oal_usb_probe success![oal_usb_system_init_config:1099]
plat_soc:E]plat handle hcc msg dev_bsp_ready_cb.
plat_soc:E]===BSP READY==
[USB][I]usb_reload succ[hcc_usb_reload:1667]
plat_soc:E]firmware_download_etc::succ!
plat_soc:W]download firmware, count [1], current time [909481]us, max time [909481]us
plat_soc:E]ini get mac_addr failed
plat_soc:W]power on, count [1], current time [1006091]us, max time [1006091]us
plat_soc:W]pm_svc_open::first svc open, pm_svc_power_on succ!
plat_soc:E]pm_svc_open::wlan open.
plat_soc:E]pm_svc_open::SUCC!
plat_soc:E]wlan_power_open_cmd
plat_soc:E]===wlan READY==
random: crng init done
hwifi_custom_adapt_mac_device_priv_ini_param::ldpc[1].
hwifi_custom_adapt_mac_device_priv_ini_param::front_switch[0].
hwifi_custom_adapt_device_priv_ini_cali_mask_param::read cali_mask[8110]ret[0]
hwifi_custom_adapt_mac_device_priv_ini_param::g_uc_wlan_open_cnt[1]priv_cali_data_up_down[0x14]
hwifi_custom_adapt_mac_device_priv_ini_param::g_uc_custom_cali_done_etc[0]auto_cali_mask[0x0]
hwifi_custom_adapt_device_priv_ini_param::data_len[46]
hwifi_hcc_custom_ini_data_buf:46 **
hwifi_hcc_custom_ini_data_buf:22 **
===hal_initialize_phy===269===
====hal_device_state_init_event=====620===21=
hwifi_get_country_code_etc suc: code:CN
hwifi_get_region 99: region not found
hwifi_get_region find CN in region_table_default
plat_soc:E]===wlan READY==
vap_id[0] {hmac_config_set_cus_dts_cali::cali time[32]ms ret[0]}
save cali data len:864 ret:0.
plat_soc:E]2a:00:73:2a:5d:b7
plat_soc:E]wlan_close_etc, exit_later_func
plat_soc:E]pm_svc_close::not rmmod svc [0], return.
wifi_host_init_finish![wifi_cali1 cost 1467 ms].
insmod wifi ko finished!
0x0, 0xf7
[FRW] frw_timer_clean_timer enter
host_main_init: host_module_init_etc return error code: 65535
do_init_module: ‘wifi_soc’->init suspiciously returned 65535, it should follow 0/-E convention
do_init_module: loading module anyway…
CPU: 0 PID: 951 Comm: insmod Tainted: G O 5.10.221 #1
Hardware name: HI35XX
[] (unwind_backtrace) from [] (show_stack+0xb/0xc)
[] (show_stack) from [] (dump_stack+0x5f/0x74)
[] (dump_stack) from [] (do_init_module+0x73/0x134)
[] (do_init_module) from [] (sys_finit_module+0x5d/0x7c)
[] (sys_finit_module) from [] (ret_fast_syscall+0x1/0x60)
Exception stack(0xc194ffa8 to 0xc194fff0)
ffa0: 43b45617 00000001 00000003 b6fdecd0 00000000 bee29f4f
ffc0: 43b45617 00000001 0000017b 0000017b 00000020 00000001 bee29e64 00000000
ffe0: bee29f4f bee29db0 00438111 b6fab2be
udhcpc: SIOCGIFINDEX: No such device
/ # Successfully initialized wpa_supplicant
Could not read interface wlan0 flags: No such device
nl80211: Driver does not support authentication/association or connect commands
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Could not read interface wlan0 flags: No such device
wlan0: Failed to initialize driver interface
wlan0: CTRL-EVENT-DSCP-POLICY clear_all

/ #
/ # lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 001 Device 003: ID ffff:3733
Bus 002 Device 001: ID 1d6b:0003
/ # ifconfig
eth0 Link encap:Ethernet HWaddr CE:3C:D3:4E:35:87
inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:80 errors:0 dropped:0 overruns:0 frame:0
TX packets:49 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:27178 (26.5 KiB) TX bytes:4546 (4.4 KiB)
Interrupt:29

我来回答
回答3个
时间排序
认可量排序

随风

2个粉丝

4

问答

0

专栏

2

资料

随风 2025-09-24 07:40:20
认可0

请问这问题解决了吗?遇到同样问题

ulockn
ulockn   回复   随风  2025-09-24 09:50:53
0

还没有😶

💫
💫   回复   随风  2025-12-01 14:52:51
0

你好这个问题请问解决了吗,我也遇到这个问题了

或将文件直接拖到这里
悬赏:
E币
网盘
* 网盘链接:
* 提取码:
悬赏:
E币

Markdown 语法

  • 加粗**内容**
  • 斜体*内容*
  • 删除线~~内容~~
  • 引用> 引用内容
  • 代码`代码`
  • 代码块```编程语言↵代码```
  • 链接[链接标题](url)
  • 无序列表- 内容
  • 有序列表1. 内容
  • 缩进内容
  • 图片![alt](url)
+ 添加网盘链接/附件

Markdown 语法

  • 加粗**内容**
  • 斜体*内容*
  • 删除线~~内容~~
  • 引用> 引用内容
  • 代码`代码`
  • 代码块```编程语言↵代码```
  • 链接[链接标题](url)
  • 无序列表- 内容
  • 有序列表1. 内容
  • 缩进内容
  • 图片![alt](url)
相关问答
无更多相似问答 去提问
举报反馈

举报类型

  • 内容涉黄/赌/毒
  • 内容侵权/抄袭
  • 政治相关
  • 涉嫌广告
  • 侮辱谩骂
  • 其他

详细说明

易百纳技术社区