请帮忙解答一下 38E板子更新2026-05-18固件开机提示要输什么密码

更新如下路径因件：
1）出厂固件包\02.Linux\Hi3516CV610-20S\Board_38E_CV610_SPINAND_Linux

，提示要输密码，请问要输什么，开机log如下：

flash
boot table board switch:0x00000000
boot table version :V0.2
boot table build time :2026/05/13 15:11:07
boot table file name :Hi3516CV610-DMEB_4L_DDR3_2133M_128MB_16bit-A7_950M_QFN.xlsm
DDR size: 0x00000080

System startup

Uncompress Ok!

U-Boot 2022.07 (May 13 2026 - 15:11:49 +0800)hi3516cv610-debug

DRAM: Relocation Offset is: 0277e000
Relocating to 43f7e000, new gd at 43b3ded0, sp at 43b3deb0
Core: 1 devices, 1 uclasses
SPI Nor: Boot Media isn’t SPI Nor
NAND: fmc_ip_ver_check(32): Check Flash Memory Controller v100 …fmc_ip_ver_check(38): Found
SPI Nand ID Table Version 2.7
SPI Nand(cs 0) ID: 0xe5 0xf1 Name:”DS35Q1GB-IB”
Block:128KB Page:2KB OOB:128B ECC:24bit/1K
Chipsize:128 MiB
MMC:
Loading Environment from SPIFlash… Boot Media isn’t SPI Nor
* Warning - spi_flash_probe() failed, using default environment

Loading Environment from NAND… OK
In: serial
Out: serial
Err: serial

Net: eth0
Error: eth0 address not set.

Hit Ctrl+C to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x400000
4194304 bytes read: OK

Loading kernel from FIT Image at 41000000 …

Using ‘config-1’ configuration
Trying ‘linux_kernel’ kernel subimage
Description: Linux
Type: Kernel Image
Compression: uncompressed
Data Start: 0x41003fa0
Data Size: 3857912 Bytes = 3.7 MiB
Architecture: ARM
OS: Linux
Load Address: 0x40018000
Entry Point: 0x40018000

Loading fdt from FIT Image at 41000000 …

Using ‘config-1’ configuration
Trying ‘fdt-1’ fdt subimage
Description: dtb
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x410000b0
Data Size: 15981 Bytes = 15.6 KiB
Architecture: ARM
Load Address: 0x40000000
Loading fdt from 0x410000b0 to 0x40000000
Booting using the fdt blob at 0x40000000

Loading loadables from FIT Image at 41000000 …

Trying ‘linux_kernel’ loadables subimage
Description: Linux
Type: Kernel Image
Compression: uncompressed
Data Start: 0x41003fa0
Data Size: 3857912 Bytes = 3.7 MiB
Architecture: ARM
OS: Linux
Load Address: 0x40018000
Entry Point: 0x40018000
Loading loadables from 0x41003fa0 to 0x40018000

Loading loadables from FIT Image at 41000000 …

Trying ‘fdt-1’ loadables subimage
Description: dtb
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x410000b0
Data Size: 15981 Bytes = 15.6 KiB
Architecture: ARM
Load Address: 0x40000000
Loading loadables from 0x410000b0 to 0x40000000
Loading Kernel Image
Using Device Tree in place at 40000000, end 40006e6c

Starting kernel …

Booting Linux on physical CPU 0x0
Linux version 5.10.221 (sunshine@sunshine-vm) (arm-v01c02-linux-musleabi-gcc (musl-1.2.3 linux-5.10 CS71.2.10.5.B002 2025-03-05 12:00:00) 10.3.0, GNU ld (GNU Binutils) 2.41) #1 SMP Wed May 13 15:13:16 CST 2026
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
OF: fdt: Machine model: Hisilicon Hi3516CV610 DEMO Board
Memory policy: Data cache writealloc
Zone ranges:
Normal [mem 0x0000000040000000-0x0000000043ffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000040000000-0x0000000043ffffff]
Initmem setup node 0 [mem 0x0000000040000000-0x0000000043ffffff]
percpu: Embedded 14 pages/cpu s26828 r8192 d22324 u57344
Built 1 zonelists, mobility grouping on. Total pages: 16256
Kernel command line: mem=64M console=ttyAMA0,115200 clk_ignore_unused rootfstype=ubifs rw ubi.mtd=3 mtdparts=nand:512K(u-boot.bin),512K(env.bin),4M(uImage),96M(rootfs.ubifs) root=ubi0:ubifs
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
mem auto-init: stack:off, heap alloc:on, heap free:off
Memory: 57188K/65536K available (4096K kernel code, 233K rwdata, 1536K rodata, 1024K init, 176K bss, 8348K reserved, 0K cma-reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
rcu: Hierarchical RCU implementation.
rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
Tracing variant of Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
arch_timer: cp15 timer(s) running at 24.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
Switching to timer-based delay loop, resolution 41ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
CPU: Testing write buffer coherency: ok
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x40100000 - 0x40100038
rcu: Hierarchical SRCU implementation.
smp: Bringing up secondary CPUs …
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated (96.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes, linear)
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Serial: AMBA PL011 UART driver
SCSI subsystem initialized
ssp-pl022 11070000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 11070000.spi: deassert reset
ssp-pl022 11071000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 11071000.spi: deassert reset
usb_ver: 5.10 - 2.3
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
mc: Linux media interface: v0.10
videodev: Linux video capture interface: v2.00
[UPS-PHY][ups_phy_module_init]registered new ups phy driver
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.22
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
clocksource: Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Initialise system trusted keyrings
workingset: timestamp_bits=30 max_order=14 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
Key type asymmetric registered
Asymmetric key parser ‘x509’ registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
brd: module loaded
loop: module loaded
bsp-sfc bsp_spi_nor.0: SPI Nor ID Table Version 1.2
bsp-sfc bsp_spi_nor.0: unrecognized Manufacturer ID
bsp-sfc bsp_spi_nor.0: spi nor register fail!
bsp-sfc: probe of bsp_spi_nor.0 failed with error -2
SPI Nand ID Table Version 2.7
SPI Nand(cs 0) ID: 0xe5 0xf1
nand: device found, Manufacturer ID: 0xe5, Chip ID: 0xf1
nand: Dosilicon DS35Q1GB-IB
nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
Nand(Auto):
OOB:128B
ECC:24bit/1k
nand: NAND_ECC_ENGINE_TYPE_NONE selected by board driver. This is not recommended!
4 cmdlinepart partitions found on MTD device nand
Creating 4 MTD partitions on “nand”:
0x000000000000-0x000000080000 : “u-boot.bin”
0x000000080000-0x000000100000 : “env.bin”
0x000000100000-0x000000500000 : “uImage”
0x000000500000-0x000006500000 : “rootfs.ubifs”
Get ld_trim_compensation -1 from dts.
FEPHY:addr=0, la_am=0xb, ldo_am=0x5, r_tuning=0x24
attached port 0 PHY 0 to driver Generic PHY
usbcore: registered new interface driver asix
usbcore: registered new interface driver ax88179_178a
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver usb-storage
bsp_rtc 11110000.rtc: registered as rtc0
bsp_rtc 11110000.rtc: setting system clock to 1970-01-02T01:09:45 UTC (90585)
bsp_rtc 11110000.rtc: RTC driver for bsp enabled
i2c /dev entries driver
bsp-i2c 11060000.i2c: deassert reset
bsp-i2c 11060000.i2c: IRQ index 0 not found
bsp-i2c 11061000.i2c: deassert reset
bsp-i2c 11061000.i2c: IRQ index 0 not found
bsp-i2c 11062000.i2c: deassert reset
bsp-i2c 11062000.i2c: IRQ index 0 not found
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
[WING-USB][wing_usb_module_init]register wing usb driver
mmc0: SDHCI controller on 10030000.SDIO [10030000.SDIO] using ADMA
mmc1: SDHCI controller on 10040000.SDIO1 [10040000.SDIO1] using ADMA
NET: Registered protocol family 17
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
Registering SWP/SWPB emulation handler
Loading compiled-in X.509 certificates
uart-pl011 11040000.uart: deassert reset
11040000.uart: ttyAMA0 at MMIO 0x11040000 (irq = 30, base_baud = 0) is a PL011 rev2
printk: console [ttyAMA0] enabled
uart-pl011 11041000.uart: deassert reset
11041000.uart: ttyAMA1 at MMIO 0x11041000 (irq = 31, base_baud = 0) is a PL011 rev2
uart-pl011 11042000.uart: deassert reset
11042000.uart: ttyAMA2 at MMIO 0x11042000 (irq = 32, base_baud = 0) is a PL011 rev2
pl061_gpio 11090000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11091000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11092000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11093000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11094000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11095000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11096000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11097000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11098000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11099000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 1109a000.gpio_chip: PL061 GPIO chip registered
ubi0: attaching mtd3
ubi0: scanning is finished
ubi0: attached mtd3 (name “rootfs.ubifs”, size 96 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 767, bad PEBs: 1, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1458845794
ubi0: available PEBs: 0, total reserved PEBs: 767, PEBs reserved for bad PEB handling: 19
ubi0: background thread “ubi_bgt0d” started, PID 759
cfg80211: Loading compiled-in X.509 certificates for regulatory database
cfg80211: Loaded X.509 cert ‘sforshee: 00b28ddf47aef9cea7’
cfg80211: Loaded X.509 cert ‘wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600’
clk: Not disabling unused clocks
ALSA device list:
No soundcards found.
platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
cfg80211: failed to load regulatory.db
UBIFS (ubi0:0): Mounting in unauthenticated mode
UBIFS (ubi0:0): background thread “ubifs_bgt0_0” started, PID 765
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name “ubifs”
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 93073408 bytes (88 MiB, 733 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID 434EC31D-C6DA-48BD-BE74-75FA3C219624, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:13.
devtmpfs: mounted
Freeing unused kernel memory: 1024K
Run /sbin/init as init process

mknod: /dev/console: File exists
mknod: /dev/ttyAMA0: File exists
mknod: /dev/null: File exists

udevd[779]: starting version 3.2.11
random: udevd: uninitialized urandom read (16 bytes read)
udevd[780]: starting eudev-3.2.11
random: udevd: uninitialized urandom read (16 bytes read)

  IP: 192.168.1.168

BOOTP:
GATEWAY: 192.168.1.1
NETMASK: 255.255.255.0
HOSTNAME:
NETDEV: eth0
AUTOCONF:

random: udevd: uninitialized urandom read (16 bytes read)
random: crng init done

os_mem_size: 64
mem_total: 128
mmz_start: 0x44000000, mmz_size: 64M
sys_config: loading out-of-tree module taints kernel.
sys_config_parse_board,185: ==========board_type: dmeb_qfn==========
sys_config_parse_board,192: g_board 1
sensor_cfg,421: ==========sensor0: sc4336p==========
sensor_cfg,421: ==========sensor1: sc4336p==========
Media Memory Zone Manager
load mmz ….OK!
ot_base: module license ‘Proprietary’ taints kernel.
Disabling lock debugging due to kernel taint
load base.ko ….OK!
load vb.ko ….OK!
load vca.ko ….OK!
load sys.ko ….OK!
load region.ko ….OK!
load vpp.ko ….OK!
load vgs.ko ….OK!
load vpss.ko ….OK!
load vi.ko ….OK!
load isp.ko ….OK!
load chnl.ko ….OK!
load rc.ko ….OK!
load venc.ko ….OK!
load h264e.ko ….OK!
load h265e.ko ….OK!
load svac3e.ko ….OK!
load jpege.ko ….OK!
load svp_npu.ko ….OK!
load ive.ko ….OK!
load pwm.ko ….OK!
load ot_piris.ko ….OK!
load sensor_i2c.ko ….OK!
load aio.ko ….OK!
load ai.ko ….OK!
load ao.ko ….OK!
load aenc.ko ….OK!
load adec.ko ….OK!
load acodec.ko ….OK!
load mipirx_dev.ko ….OK!
load aiisp.ko ….OK!
load uvc.ko ….OK!
load pm.ko ….OK!
load cipher.ko success!
load km.ko success!
/

Please press Enter to activate this console. xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe6d hci version 0x110 quirks 0x0000000020010010
xhci-hcd xhci-hcd.0.auto: irq 72, io mem 0x10300000
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb2: We don’t know the algorithms for LPM for this host, disabling LPM.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: config failed, hub doesn’t have any ports! (err -19)

(none) login:
(none) login:
(none) login: ROOT^H^H^H^H
Password:

^ZLogin incorrect
login[1210]: invalid password for ‘UNKNOWN’ on ‘ttyAMA0’
(none) login: ^C^H
Please press Enter to activate this console. ^H
(none) login: root
Password:
Login incorrect
login[1228]: invalid password for ‘root’ on ‘ttyAMA0’