技术专栏
nvidia xavier平台无PD控制器USB接口调试
1. 前言
问题：
基于nvidia xavier核心板，设计载板，但是USB功能无法使用；
硬件：
OTG连接器使用Micro B
VBUS_ID=GPIO30(B55) pin
VBUS Detect=GPIO10(A62)
检查了USB端口VBUS pin保持5V在我们携带的板上
咨询nvidia技术人员，说是没有PD控制器，所以需要对dts进行修改调试
2. 参考修改
对于类型A，没有OTG，如果没有PD控制器，需要删除xhci和xudc下的extcon-*属性。
还需要添加一个调节器“vbus-supply”下的xusb_pad_ctl一些usb2端口伴随USB3.0端口。
必须在设备树中编写自己的extcon(如果需要使用OTG)。
vbus_id_extcon: extcon@1 {
compatible = "extcon-gpio-states";
extcon-gpio,name = "VBUS_ID";
extcon-gpio,wait-for-gpio-scan = <0>;
extcon-gpio,cable-states = <0x3 0x0
0x0 0x2
0x1 0x2
0x2 0x1>;
gpios = <&tegra_main_gpio TEGRA194_MAIN_GPIO(M, 3) 0
&tegra_main_gpio TEGRA194_MAIN_GPIO(Q, 0) 0>;
//GPIO_M3 is VBUS_DETECT pin and GPIO_Q0 is ID pin.
extcon-gpio,out-cable-names = <EXTCON_USB EXTCON_USB_HOST EXTCON_NONE>;
#extcon-cells = <1>;
};对于extcon节点，
可参考“kernel/kernel-4.9/Documentation/devicetree/bindings/extcon/extcon-gpio-states.txt”
创建这个节点后，在xhci/xudc下的属性节点下面设置
extcon-cables = <&vbus_id_extcon 1>;
extcon-cable-names = "id";
#extcon-cells = <1>;
under xudc
extcon-cables = <&vbus_id_extcon 0>;
extcon-cable-names = "vbus";
#extcon-cells = <1>;注意事项:
（1）extcon-cables: OTG支持。必须包含一个检测USB ID pin的extconcable入口。当extcon线缆状态为0时，OTG端口将转换为主机模式。
（2）xhci必须为“id”，xudc必须为“vbus”。
（3）#extcon-cells: extcon说明符中的单元数。总是应该是1。
如果不需要OTG，删除xhci/xudc下的extcon相关属性
3. dts具体修改
1. under ucsi_ccg
ucsi_ccg: ucsi_ccg@8 {
- status = "okay";
+ status = "disabled";
2. under xusb_padctl@3520000, make sure mode is set to "host" and usb3 ports need its companion usb2 port.
xusb_padctl: xusb_padctl@3520000 {
......
ports {
usb2-0 {
mode = "host";
status = "okay";
};
usb3-0 {
status = "okay";
nvidia,usb2-companion = <0x0>; //it means the port is coupled with usb2-0
};
};
3. add regulator for vbus-supply
//I don't know how is your hw design this part. You need to add those regulators for them.
+ vdd_usb20_5v0: regulator@115 {
+ compatible = "regulator-fixed";
+ reg = <115>;
+ regulator-name = "vdd-usb20-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&tegra_main_gpio TEGRA194_MAIN_GPIO(Z, 1) 0>;
+ vin-supply = <&battery_reg>;
+ };
ports {
usb2-0 {
- vbus-supply = <&battery_reg>;
+ vbus-supply = <&vdd_usb20_5v0>;
};
4. remove all "extcon*" property under xhci@3610000 and xudc@3550000.4. 修改后完整dts如下
/ {
nvidia,dtsfilename = __FILE__;
nvidia,dtbbuildtime = __DATE__, __TIME__;
nvidia,fastboot-usb-vid = <0x0955>;
nvidia,fastboot-usb-pid = <0xee1e>;
model = "jetson-xavier";
compatible = "nvidia,jetson-xavier", "nvidia,tegra194";
chosen {
bootargs ="console=ttyTCU0,115200";
board-has-eeprom;
};
firmware {
android {
compatible = "android,firmware";
hardware = "jetson-xavier";
fstab {
compatible = "android,fstab";
vendor {
compatible = "android,vendor";
dev = "/dev/block/platform/3460000.sdhci/by-name/vendor";
type = "ext4";
mnt_flags = "ro";
fsmgr_flags = "wait";
};
odm {
compatible = "android,odm";
dev = "/dev/block/platform/3460000.sdhci/by-name/odm";
type = "ext4";
mnt_flags = "ro";
fsmgr_flags = "wait";
};
};
};
};
arm64_ras {
status = "okay";
};
carmel_ras {
status = "okay";
};
spi@3270000 {
status = "disabled";
};
spi@3300000 {
status = "disabled";
};
pmc@c370000 {
nvidia,invert-interrupt;
};
i2c@c240000 {
ucsi_ccg: ucsi_ccg@8 {
status = "disabled";
typec-extcon {
typec_port0: port-0 {
status = "okay";
#extcon-cells = <1>;
};
typec_port1: port-1 {
status = "okay";
#extcon-cells = <1>;
};
};
typec-pd {
typec_pd: pd {
status = "okay";
#extcon-cells = <1>;
};
};
};
};
#if TEGRA_XUSB_PADCONTROL_VERSION >= DT_VERSION_2
xusb_padctl: xusb_padctl@3520000 {
status = "okay";
pads {
usb2 {
lanes {
usb2-0 {
nvidia,function = "xusb";
status = "okay";
};
usb2-1 {
nvidia,function = "xusb";
status = "okay";
};
usb2-2 {
nvidia,function = "xusb";
status = "okay";
};
usb2-3 {
nvidia,function = "xusb";
status = "okay";
};
};
};
usb3 {
lanes {
usb3-0 {
nvidia,function = "xusb";
status = "okay";
};
usb3-2 {
nvidia,function = "xusb";
status = "okay";
};
usb3-3 {
nvidia,function = "xusb";
status = "okay";
};
};
};
};
ports {
usb2-0 {
mode = "host";
//vbus-supply = <&battery_reg>;
status = "okay";
};
usb2-1 {
mode = "host";
status = "okay";
};
usb2-2 {
mode = "host";
status = "okay";
};
usb2-3 {
mode = "host";
status = "okay";
};
usb3-0 {
nvidia,usb2-companion = <0x0>;
status = "okay";
};
usb3-2 {
nvidia,usb2-companion = <0>;
status = "okay";
};
usb3-3 {
nvidia,usb2-companion = <3>;
nvidia,usb3-gen1-only= <1>;
status = "okay";
};
};
};
#endif
tegra_xudc: xudc@3550000 {
/*extcon-cables = <&typec_port0 0>;
extcon-cable-names = "vbus";
#extcon-cells = <1>;*/
#if TEGRA_XUSB_PADCONTROL_VERSION >= DT_VERSION_2
phys = <&{/xusb_padctl@3520000/pads/usb2/lanes/usb2-0}>,
<&{/xusb_padctl@3520000/pads/usb3/lanes/usb3-2}>;
phy-names = "usb2", "usb3";
nvidia,xusb-padctl = <&xusb_padctl>;
#endif
status = "okay";
};
tegra_xhci: xhci@3610000 {
/*extcon-cables = <&typec_port0 1>;
extcon-cable-names = "id";
#extcon-cells = <1>;*/
#if TEGRA_XUSB_PADCONTROL_VERSION >= DT_VERSION_2
phys = <&{/xusb_padctl@3520000/pads/usb2/lanes/usb2-0}>,
<&{/xusb_padctl@3520000/pads/usb2/lanes/usb2-1}>,
<&{/xusb_padctl@3520000/pads/usb2/lanes/usb2-3}>,
<&{/xusb_padctl@3520000/pads/usb2/lanes/usb2-2}>,
<&{/xusb_padctl@3520000/pads/usb3/lanes/usb3-2}>,
<&{/xusb_padctl@3520000/pads/usb3/lanes/usb3-0}>,
<&{/xusb_padctl@3520000/pads/usb3/lanes/usb3-3}>;
phy-names = "usb2-0", "usb2-1", "usb2-3", "usb2-2",
"usb3-2", "usb3-0", "usb3-3";
nvidia,xusb-padctl = <&xusb_padctl>;
#endif
status = "okay";
};
arm-pmu {
status = "okay";
};
power-domain {
status = "disabled";
};
interrupt-controller {
status = "disabled";
};
mods-simple-bus {
status = "disabled";
};
eeprom-manager {
status = "disabled";
};
cpuidle {
compatible = "nvidia,tegra19x-cpuidle";
status = "okay";
};
thermal-zones {
status = "disabled";
};
reserved-memory {
ramoops_carveout {
status = "okay";
};
};
mttcan@c310000 {
status = "okay";
};
mttcan@c320000 {
status = "okay";
};
serial@3110000 {
status = "okay";
};
pwm@32c0000 {
status = "okay";
};
pwm@32f0000 {
status = "okay";
};
i2c@31e0000 {
pinctrl-names = "default";
pinctrl-0 = <&dpaux_default>;
bmi160@69 {
compatible = "bmi,bmi160";
reg = <0x69>;
accelerometer_matrix = [01 00 00 00 01 00 00 00 01];
gyroscope_matrix = [01 00 00 00 01 00 00 00 01];
status = "okay";
};
};
host1x {
dpaux@155F0000 {
status = "okay";
compatible = "nvidia,tegra194-dpaux3-padctl";
/delete-property/ power-domains;
dpaux_default: pinmux@0 {
dpaux3_pins {
pins = "dpaux3-3";
function = "i2c";
};
};
};
};
hardwood {
compatible = "nvidia,denver-hardwood";
interrupts = <0 24 0x4>;
};
ufshci@2450000 {
nvidia,enable-hs-mode;
};
};
/*
&head0 {
extcon-cables = <&typec_port0 2 &typec_port1 2>;
extcon-cable-names = "typec0", "typec1";
#extcon-cells = <1>;
};
&head1 {
extcon-cables = <&typec_port0 2 &typec_port1 2>;
extcon-cable-names = "typec0", "typec1";
#extcon-cells = <1>;
};
&head2 {
extcon-cables = <&typec_port0 2 &typec_port1 2>;
extcon-cable-names = "typec0", "typec1";
#extcon-cells = <1>;
};
*/
&sor0 {
nvidia,typec-port = /bits/ 8 <0>;
};
&sor1 {
nvidia,typec-port = /bits/ 8 <1>;
};
#if LINUX_VERSION >= 414
#include <tegra194-linux-4.14.dtsi>
#endif5. 调试记录
修改完后，系统一直报错，如下：
[ 468.481055] usb usb2-port4: cannot disable (err = -32)
[ 469.968830] tegra-xusb 3610000.xhci: Cannot set link state.
[ 469.969036] usb usb2-port4: cannot disable (err = -32)
[ 469.969195] tegra-xusb 3610000.xhci: Cannot set link state.
[ 469.969313] usb usb2-port4: cannot disable (err = -32)
[ 472.313439] usb 2-4: Device not responding to setup address.
[ 472.521413] usb 2-4: Device not responding to setup address.
[ 472.728640] usb 2-4: device not accepting address 66, error -71
[ 472.728848] tegra-xusb 3610000.xhci: Cannot set link state.
[ 472.728994] usb usb2-port4: cannot disable (err = -32)
[ 474.216900] tegra-xusb 3610000.xhci: Cannot set link state.
[ 474.217099] usb usb2-port4: cannot disable (err = -32)
[ 474.217261] tegra-xusb 3610000.xhci: Cannot set link state.
[ 474.217378] usb usb2-port4: cannot disable (err = -32)
nvidia@jetson-0424418058605:~$ [ 476.561449] usb 2-4: Device not responding to setup address.
[ 476.769406] usb 2-4: Device not responding to setup address.
[ 476.976634] usb 2-4: device not accepting address 68, error -71
[ 476.976859] tegra-xusb 3610000.xhci: Cannot set link state.
[ 476.977018] usb usb2-port4: cannot disable (err = -32)
nvidia@jetson-0424418058605:~$ [ 478.464874] tegra-xusb 3610000.xhci: Cannot set link state.
[ 478.465153] usb usb2-port4: cannot disable (err = -32)
[ 478.465334] tegra-xusb 3610000.xhci: Cannot set link state.
[ 478.465456] usb usb2-port4: cannot disable (err = -32)
查看usb设备信息
nvidia@jetson-0424218031082:~$ lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 8087:0a2b Intel Corp.
Bus 001 Device 005: ID 1c4f:000e SiGma Micro Genius KB-120 Keyboard
Bus 001 Device 004: ID 093a:2510 Pixart Imaging, Inc. Optical Mouse
Bus 001 Device 002: ID 8564:4100 Transcend Information, Inc.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
nvidia@jetson-0424218031082:~$
nvidia@jetson-0424218031082:~$
nvidia@jetson-0424218031082:~$ lsusb -t
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=tegra-xusb/4p, 10000M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=tegra-xusb/4p, 480M
|__ Port 2: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
|__ Port 1: Dev 4, If 0, Class=Human Interface Device, Driver=usbhid, 1.5M
|__ Port 2: Dev 5, If 0, Class=Human Interface Device, Driver=usbhid, 1.5M
|__ Port 2: Dev 5, If 1, Class=Human Interface Device, Driver=usbhid, 1.5M
|__ Port 3: Dev 3, If 0, Class=Wireless, Driver=btusb, 12M
|__ Port 3: Dev 3, If 1, Class=Wireless, Driver=btusb, 12M
nvidia@jetson-0424218031082:~$6. 调试方法
这里包含xhci日志的完整内核消息，可以方便进一步调试
echo ‘module usbcore +p’ > /sys/kernel/debug/dynamic_debug/control
echo ‘module xhci_hcd +p’ > /sys/kernel/debug/dynamic_debug/control
echo 8 > /proc/sys/kernel/printk7. 修改usb2-companion
通过进一步排查发现是如下设置出现问题
usb3-0 {
nvidia,usb2-companion = <0x0>;
status = "okay";
};
usb3-2 {
nvidia,usb2-companion = <0>;
status = "okay";
｝；这里表示usb3-0和usb3-2都使用相同的usb2-0端口0；
与实际硬件是不符合的
修改如下：
usb3-0 {
nvidia,usb2-companion = <0x0>;
status = "okay";
};
usb3-2 {
nvidia,usb2-companion = <1>;
status = "okay";
};
usb3-3 {
nvidia,usb2-companion = <3>;
nvidia,usb3-gen1-only= <1>;
status = "okay";
};至此调过PD控制器， USB接口可正常使用
声明：本文内容由易百纳平台入驻作者撰写，文章观点仅代表作者本人，不代表易百纳立场。如有内容侵权或者其他问题，请联系本站进行删除。
红包
97
8
评论
打赏
- 分享
- 举报
微信扫码分享
QQ好友
评论
0个
手气红包
暂无数据相关专栏
-
浏览量：6020次2021-04-21 17:42:58
-
浏览量：4893次2021-07-17 15:37:58
-
浏览量：6881次2021-05-11 17:51:48
-
浏览量：7990次2021-05-14 14:43:43
-
浏览量：1786次2020-02-24 09:57:27
-
浏览量：8824次2021-04-27 17:56:41
-
浏览量：10645次2021-02-05 14:30:37
-
浏览量：8613次2021-05-26 14:17:15
-
2021-05-06 16:03:00
-
浏览量：10003次2021-05-06 16:22:01
-
浏览量：15601次2021-02-19 17:01:32
-
浏览量：6594次2021-05-11 17:04:57
-
浏览量：4906次2021-05-10 17:48:42
-
浏览量：6603次2021-05-27 16:16:56
-
浏览量：8633次2021-05-19 17:32:00
-
浏览量：8766次2021-05-25 17:31:40
-
浏览量：6982次2021-05-20 17:08:14
-
浏览量：6528次2021-05-20 16:37:42
-
浏览量：7372次2021-05-25 15:32:16
关于作者
free-jdx
暂无个性签名~
原创178
阅读108.7w
收藏13
点赞35
评论24
切换马甲
上一页
下一页
打赏用户
共 1 位
我要创作
分享技术经验，可获取创作收益
分类专栏
-
178篇
热门专栏
- NVIDIA加速GPU协同ARM64开启高性能计算新篇章
- 英伟达将取消的RTX 4080恢复为“新”12GB RTX 4070 TI
- nvidia xavier平台lan7800网卡驱动调试记录（2）网卡硬件& patch验证
- 全新GeForce GTX 900M发布！让笔记本游戏性能更强大
- 八连胜！NVIDIA GPU加速系统再次成就冠军队伍！
- TITAN BLACK梦幻作品！GeForce Garage交叉书桌打造日志
- 两天精彩让你High翻天！NGF 2014观展指南
- 助力转型：GPU如何完成曾经不可能完成的分析工作
- 15年，提名奥斯卡视觉特效的电影皆由NVIDIA的技术所呈现
- 先睹为快: 黄仁勋秀GTX780Ti
置顶时间设置
结束时间
删除原因
-
广告/SPAM
-
恶意灌水
-
违规内容
-
文不对题
-
重复发帖
打赏作者
free-jdx
您的支持将鼓励我继续创作！
打赏金额：
￥1
￥5
￥10
￥50
￥100
支付方式：
微信支付
举报反馈
举报类型
- 内容涉黄/赌/毒
- 内容侵权/抄袭
- 政治相关
- 涉嫌广告
- 侮辱谩骂
- 其他
详细说明
审核成功
发布时间设置
发布时间：
请选择发布时间设置
是否关联周任务-专栏模块
审核失败
失败原因
请选择失败原因
备注
请输入备注
关注公众号
联系我们
社区问题咨询：Ebaina-CN
定制需求咨询：xxqk158820
社区问题咨询：Ebaina-CN
定制需求咨询：xxqk158820
回顶部
