海思3516dv500平台，ot_isp_pub_attr参数设置不当导致sensor不能正常出图，请教其中详细的含义

请问初始化序列要核对那些地方？现在用的序列就是原厂直接给的，我们提供位宽/输入时钟/帧率/同步模式等信息给他们。感觉这个应该问题不大

mipi_rx信息如下，mipi_data是会变化的：

Module: [MIPI_RX], Build Time[May  7 2025, 17:09:56]


-----mipi lane divide mode---------------------------------------------------------------------------------------------
  mode         lane divide
     0                   8

-----mipi dev attr-----------------------------------------------------------------------------------------------------
   devno  work_mode  data_rate           data_type  wdr_mode   img_x   img_y   img_w   img_h
       0       mipi         X1               raw12      none       0       0    3840    2184

-----mipi lane info-----------------------------------------------------------------------------------------------------
   devno                 lane_id                    speed_mode
       0         0,  1,  2,  3, -1, -1, -1, -1      LE1500Mbps

-----mipi clk info-----------------------------------------------------------------------------------------------------
   devno     enable
       0          Y

------sns clk info-----------------------------------------------------------------------------------------------------
   devno     enable
       1          Y

-----mipi phy data info------------------------------------------------------
  phy_id        lane_id           phy_data               mipi_data             lvds_data            freq
       0       0, 1, 2, 3    0x00,0x00,0x00,0x00    0x00,0x00,0x00,0x00    0x00,0x00,0x00,0x03    148MHZ
       1       4, 5, 6, 7    0x00,0x00,0x00,0x00    0x00,0x00,0x00,0x00    0x00,0x00,0x00,0x00       n/a

-----mipi detect info----------------------------------------------------
 devno vc   width  height
     0  0    3840    2180
     0  1       0       0
     0  2       0       0
     0  3       0       0

-----phy cil err int info---------------------------------------------
  phy_id clk2_tmout clk_tmout lane0_tmout lane1_tmout lane2_tmout lane3_tmout clk2_esc clk_esc lane0_esc lane1_esc lane2_esc lane3_esc
       0          0         0           0           0           0           0        0       0         0         0         0         0
       1          0         0           0           0           0           0        0       0         0         0         0         0

-----mipi error int info1-----------------------------------------------------------
   devno  ecc2  vc0_crc  vc1_crc  vc2_crc  vc3_crc  vc0_ecc_correct  vc1_ecc_correct  vc2_ecc_correct  vc3_ecc_correct
       0     0        0        0        0        0                0                0                0                0

-----mipi error int info2-----------------------------------------------------------
   devno  vc0_frmnum  vc1_frmnum  vc2_frmnum  vc3_frmnum  vc0_frmmmatch  vc1_frmmmatch  vc2_frmmmatch  vc3_frmmmatch
       0           0           0           0           0              0              0              0              0

-----mipi error int info3-----------------------------------------------------------
   devno  data_fifo_rderr  cmd_fifo_rderr  vsync  cmd_fifo_wrerr  data_fifo_wrerr
       0                0               0      0               0                0

-----align error int info--------------------------------------
   devno  fifo_fullerr  lane0_err  lane1_err  lane2_err  lane3_err  lane4_err  lane5_err  lane6_err  lane7_err
       0             0          0          0          0          0          0          0          0          0

-----mipi dbg info-----------------------------------------------------------------------------------------------------
   phyno      skew_len0      skew_len1

这个宽只有3840，如果你偏移了8个像素再取3840的数据就取不到了，高度有2180，偏移10再取2160是没问题的

原来是以mipi控制器检测到的总宽高为准，非常感谢指点！