使用SD卡烧录固件，无法进入系统

System startup

Uncompress Ok!

U-Boot 2020.01 (Jul 31 2024 - 09:54:43 +0000)ss928v100

DRAM: Relocation Offset is: 17744000
Relocating to 5ff44000, new gd at 5fd23df8, sp at 5fd23de0
MMC: MMC/SD Card:
MID: 0x9b
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 59648M Bytes (High Capacity)
Name: “Y0S06”
Chip Type: MMC
Version: 5.1
Speed: 200000000Hz
Bus Width: 8bit
Mode: HS400ES
bsp-sdhci: 0 (eMMC), bsp-sdhci: 1 (SD)
Loading Environment from MMC… OK
In: serial
Out: serial
Err: serial

Net: gmac0
Error: gmac0 address not set.
, gmac1
Error: gmac1 address not set.

Unrecognized filesystem type
2455 bytes read in 6 ms (399.4 KiB/s)
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
Unrecognized filesystem type
cpfile:mmc 1:1 /boot/boot_image_8G.bin
[=================================================>] 100%
cpfile:mmc 1:1 /boot/boot_env_8G.bin
[=================================================>] 100%
cpfile:mmc 1:1 /boot/kernel
[=================================================>] 100%
cpfile:mmc 1:1 /boot/rootfs.ext4
[=================================================>] 100%
resetting …

System startup

Uncompress Ok!

U-Boot 2020.01 (Jul 31 2024 - 09:54:43 +0000)ss928v100

DRAM: Relocation Offset is: 17744000
Relocating to 5ff44000, new gd at 5fd23df8, sp at 5fd23de0
MMC: MMC/SD Card:
MID: 0x9b
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 59648M Bytes (High Capacity)
Name: “Y0S06”
Chip Type: MMC
Version: 5.1
Speed: 200000000Hz
Bus Width: 8bit
Mode: HS400ES
bsp-sdhci: 0 (eMMC), bsp-sdhci: 1 (SD)
Loading Environment from MMC… OK
In: serial
Out: serial
Err: serial

Net: gmac0
Error: gmac0 address not set.
, gmac1
Error: gmac1 address not set.

Unrecognized filesystem type
2455 bytes read in 6 ms (399.4 KiB/s)
Hit any key to stop autoboot: 0

MMC read: dev # 0, block # 4096, count 32768 … 32768 blocks read: OK
303.30 MB/s
Load fip from 0x0000000042000000 …

Firmware Image Package ToC:

• EL3 Runtime Firmware BL3-1: offset=0x88, size=0x60C8
• Non-Trusted Firmware BL3-3: offset=0x6150, size=0xEB64A2

Create Entry Point info …
Get - EL3 Runtime Firmware BL3-1
Get - Non-Trusted Firmware BL3-3
kernel_size[0xeb64a2] fdt_size[0x5c5a] fdt_addr[0x0000000050f30808]
hdr[0x000000005007ffc0] header_size[0x40] image_size[0xeb0848]
bl33_ep->spsr = 0x3c5 bl33_ep->pc = 0x50080000
NOTICE: BL31: v2.2(release):ss928v100
NOTICE: BL31: Built : 08:11:04, Aug 5 2024
130 printk messages dropped
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
TCP: Hash tables configured (established 65536 bind 65536)
UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
hw perfevents: no interrupt-affinity property for /pmu, guessing.
hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
Initialise system trusted keyrings
workingset: timestamp_bits=46 max_order=21 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse: init (API version 7.33)
SGI XFS with ACLs, security attributes, realtime, quota, no debug enabled
Key type asymmetric registered
Asymmetric key parser ‘x509’ registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
io scheduler mq-deadline registered
io scheduler kyber registered
arm-smmu-v3 14040000.smmu_npu: option vendor,broken-prefetch-cmd
arm-smmu-v3 15410000.smmu_pqp: option vendor,broken-prefetch-cmd
cacheinfo: Unable to detect cache hierarchy for CPU 0
brd: module loaded
loop: module loaded
CAN device driver interface
gmac_v200 10290000.ethernet: invalid resource
attached PHY 1 to driver Generic PHY, PHY_ID=0x1cc916
ETH: rgmii, phy_addr=1
gmac_v200 102a0000.ethernet: invalid resource
attached PHY 1 to driver Generic PHY, PHY_ID=0x1cc916
ETH: rgmii, phy_addr=1
usbcore: registered new interface driver r8152
usbcore: registered new interface driver asix
usbcore: registered new interface driver ax88179_178a
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver qmi_wwan
xhci-hcd 10300000.xhci_0: xHCI Host Controller
xhci-hcd 10300000.xhci_0: new USB bus registered, assigned bus number 1
xhci-hcd 10300000.xhci_0: hcc params 0x0220fe6d hci version 0x110 quirks 0x0000000020010010
xhci-hcd 10300000.xhci_0: irq 55, io mem 0x10300000
xhci-hcd 10300000.xhci_0: xHCI Host Controller
xhci-hcd 10300000.xhci_0: new USB bus registered, assigned bus number 2
xhci-hcd 10300000.xhci_0: Host supports USB 3.0 SuperSpeed
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb2: We don’t know the algorithms for LPM for this host, disabling LPM.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
xhci-hcd 10320000.xhci_1: xHCI Host Controller
xhci-hcd 10320000.xhci_1: new USB bus registered, assigned bus number 3
xhci-hcd 10320000.xhci_1: hcc params 0x0220fe6d hci version 0x110 quirks 0x0000000020010010
xhci-hcd 10320000.xhci_1: irq 56, io mem 0x10320000
xhci-hcd 10320000.xhci_1: xHCI Host Controller
xhci-hcd 10320000.xhci_1: new USB bus registered, assigned bus number 4
xhci-hcd 10320000.xhci_1: Host supports USB 3.0 SuperSpeed
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
usb usb4: We don’t know the algorithms for LPM for this host, disabling LPM.
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver uas
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
usbcore: registered new interface driver cp210x
usbserial: USB Serial support registered for cp210x
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
udc-core: couldn’t find an available UDC - added [g_ether] to list of pending drivers
gadgetfs: USB Gadget filesystem, version 24 Aug 2004
file system registered
udc-core: couldn’t find an available UDC - added [g_cdc] to list of pending drivers
udc-core: couldn’t find an available UDC - added [g_multi] to list of pending drivers
udc-core: couldn’t find an available UDC - added [g_ncm] to list of pending drivers
udc-core: couldn’t find an available UDC - added [g_acm_ms] to list of pending drivers
vhci_hcd vhci_hcd.0: USB/IP Virtual Host Controller
vhci_hcd vhci_hcd.0: new USB bus registered, assigned bus number 5
vhci_hcd: vhci_start:1247: created sysfs vhci_hcd.0
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
vhci_hcd vhci_hcd.0: USB/IP Virtual Host Controller
vhci_hcd vhci_hcd.0: new USB bus registered, assigned bus number 6
usb usb6: We don’t know the algorithms for LPM for this host, disabling LPM.
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 8 ports detected
usbcore: registered new device driver usbip-host
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 1a:c4:95:fa:91:8b
usb0: MAC 42:98:60:ee:37:a0
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
bsp-i2c 11060000.i2c: IRQ index 0 not found
bsp-i2c 11060000.i2c: wait idle timeout, RIS: 0x10, SR: 0xa0000
rtc-pcf8563 0-0051: pcf8563_write_block_data: err=-5 addr=0e, data=03
rtc-pcf8563 0-0051: pcf8563_probe: write error
rtc-pcf8563: probe of 0-0051 failed with error -5
bsp-i2c 11061000.i2c: IRQ index 0 not found
bsp-i2c 11062000.i2c: IRQ index 0 not found
bsp-i2c 11063000.i2c: IRQ index 0 not found
bsp-i2c 11064000.i2c: IRQ index 0 not found
bsp-i2c 11065000.i2c: IRQ index 0 not found
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on 10020000.eMMC [10020000.eMMC] using ADMA 64-bit
mmc1: SDHCI controller on 10030000.SDIO [10030000.SDIO] using ADMA 64-bit
mmc2: SDHCI controller on 10040000.SDIO1 [10040000.SDIO1] using ADMA 64-bit
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
svm svm_npu@14020000: svm probe ok.
svm svm_pqp@15400000: svm probe ok.
NET: Registered protocol family 10
Segment Routing with IPv6
NET: Registered protocol family 17
can: controller area network core
NET: Registered protocol family 29
can: raw protocol
can: broadcast manager protocol
can: netlink gateway - max_hops=1
Loading compiled-in X.509 certificates
11040000.uart: ttyAMA0 at MMIO 0x11040000 (irq = 19, base_baud = 0) is a PL011 rev2
mmc0: new HS400 Enhanced strobe MMC card at address 0001
printk: console [ttyAMA0] enabled
mmcblk0: mmc0:0001 Y0S064 58.3 GiB
11041000.uart: ttyAMA1 at MMIO 0x11041000 (irq = 20, base_baud = 0) is a PL011 rev2
mmcblk0boot0: mmc0:0001 Y0S064 partition 1 4.00 MiB
11042000.uart: ttyAMA2 at MMIO 0x11042000 (irq = 21, base_baud = 0) is a PL011 rev2
mmcblk0boot1: mmc0:0001 Y0S064 partition 2 4.00 MiB
11043000.uart: ttyAMA3 at MMIO 0x11043000 (irq = 22, base_baud = 0) is a PL011 rev2
mmcblk0rpmb: mmc0:0001 Y0S064 partition 3 16.0 MiB, chardev (249:0)
11044000.uart: ttyAMA4 at MMIO 0x11044000 (irq = 23, base_baud = 0) is a PL011 rev2
mmcblk0: p1(boot) p2(env) p3(kernel) p4(rootfs)
11045000.uart: ttyAMA5 at MMIO 0x11045000 (irq = 24, base_baud = 0) is a PL011 rev2
usb 1-1: new full-speed USB device number 2 using xhci-hcd
usb 3-1: new high-speed USB device number 2 using xhci-hcd
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 5 ports detected
pl061_gpio 11090000.gpio_chip: PL061 GPIO chip registered
usb 4-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
hub 4-1:1.0: USB hub found
pl061_gpio 11091000.gpio_chip: PL061 GPIO chip registered
hub 4-1:1.0: 4 ports detected
mmc1: tuning done! valid phase shift [16, 14] Final Phase:31
mmc1: new ultra high speed SDR104 SDXC card at address aaaa
pl061_gpio 11092000.gpio_chip: PL061 GPIO chip registered
mmcblk1: mmc1:aaaa SD64G 59.5 GiB
mmcblk1: p1
pl061_gpio 11093000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11094000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11095000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11096000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11097000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11098000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11099000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 1109a000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 1109b000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 1109c000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 1109d000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 1109e000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 1109f000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 110a0000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 110a1000.gpio_chip: PL061 GPIO chip registered
mcp251x spi0.0 can0: MCP2515 successfully initialized.
cfg80211: Loading compiled-in X.509 certificates for regulatory database
cfg80211: Loaded X.509 cert ‘sforshee: 00b28ddf47aef9cea7’
clk: Not disabling unused clocks
ALSA device list:
No soundcards found.
platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
cfg80211: failed to load regulatory.db
uart-pl011 11040000.uart: no DMA platform data
EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 179:4.
devtmpfs: mounted
Freeing unused kernel memory: 1536K
Run /sbin/init as init process
starting pid 1193, tty ‘’: ‘/bin/mount -t proc proc /proc’
starting pid 1194, tty ‘’: ‘/bin/mount -t sysfs sysfs /sys’
starting pid 1195, tty ‘’: ‘/bin/mount -t devtmpfs devtmpfs /dev’
mount: mounting devtmpfs on /dev failed: Device or resource busy
starting pid 1196, tty ‘’: ‘/bin/mount -o remount,rw /‘
EXT4-fs (mmcblk0p4): re-mounted. Opts: (null)
starting pid 1197, tty ‘’: ‘/bin/mkdir -p /dev/shm’
starting pid 1198, tty ‘’: ‘/bin/mkdir -p /dev/pts’
starting pid 1199, tty ‘’: ‘/bin/mount -a’
starting pid 1200, tty ‘’: ‘/sbin/swapon -a’
usb 3-1.5: new high-speed USB device number 3 using xhci-hcd
starting pid 1206, tty ‘’: ‘/etc/init.d/rcS’
Starting mdev… OK
EXT4-fs (mmcblk0p4): re-mounted. Opts: (null)
sysctl: cannot stat /proc/sys/net/ipv4/tcp_syncookies: No such file or directory
hwclock: can’t open ‘/dev/misc/rtc’: No such file or directory
Fri Mar 9 12:34:56 UTC 2018
hwclock: can’t open ‘/dev/misc/rtc’: No such file or directory
FAT-fs (mmcblk1p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
random: dd: uninitialized urandom read (512 bytes read)
Configuring packages on first boot….
(This may take several minutes. Please do not power off the machine.)
Running postinst /etc/rpm-postinsts/100-ca-certificates…
update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing)
Removing any system startup links for run-postinsts …
/etc/rcS.d/S99run-postinsts
Configuring network interfaces… done.
random: dbus-uuidgen: uninitialized urandom read (12 bytes read)
random: dbus-uuidgen: uninitialized urandom read (8 bytes read)
Starting system message bus: random: dbus-daemon: uninitialized urandom read (12 bytes read)
dbus.
Starting OpenBSD Secure Shell server: sshd
generating ssh RSA host key…
random: crng init done
random: 1 urandom warning(s) missed due to ratelimiting
generating ssh ECDSA host key…
generating ssh ED25519 host key…
done.
starting statd: done
Starting audit daemon auditd
1
Starting bluetooth: bluetoothd.
Starting DHCP server: .
Starting HOSTAP Daemon: Could not read interface wlan0 flags: No such device
nl80211: Driver does not support authentication/association or connect commands
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Could not read interface wlan0 flags: No such device
nl80211 driver initialization failed.
wlan0: interface state UNINITIALIZED->DISABLED
wlan0: AP-DISABLED
wlan0: CTRL-EVENT-TERMINATING
hostapd_free_hapd_data: Interface wlan0 wasn’t started
hwclock: can’t open ‘/dev/misc/rtc’: No such file or directory
starting rsyslogd … done
Cleaning up tmp :
Setting up interface lo:
System booting cost:16.50 49.53
i2c_soft: loading out-of-tree module taints kernel.
soft-i2c 0.i2c: freq:1000000
soft-i2c 1.i2c: freq:1000000
mmz_start: 0x1d0000000, mmz_size: 1792M
sensor_cfg,486: ==========sensor0: os08a20==========
sensor_cfg,486: ==========sensor1: os08a20==========
sensor_cfg,486: ==========sensor2: os08a20==========
sensor_cfg,486: ==========sensor3: os08a20==========
Module ot_media: init ok
Media Memory Zone Manager
load ot_osal 1.0 ….OK!
load sys.ko ….OK!
load tde.ko ….OK!
load region.ko ….OK!
load gdc.ko ….OK!
load vpp.ko ….OK!
load vgs.ko ….OK!
load dis.ko ….OK!
load vpss.ko ….OK!
load vi.ko ….OK!
load isp.ko ….OK!
load svp_npu.ko ….OK!
load mcf.ko ….OK!
load avs.ko ….OK!
load vo.ko ….OK!
load gfbg.ko ….OK!
load chnl.ko ….OK!
load vedu.ko ….OK!
load rc.ko ….OK!
load venc.ko ….OK!
load h264e.ko ….OK!
load h265e.ko ….OK!
load jpege.ko ….OK!
load jpegd.ko ….OK!
load vfmw.ko ….OK!
load vdec.ko ….OK!
load uvc.ko ….OK!
load ive.ko ….OK!
load dpu_rect.ko ….OK!
load dpu_match.ko ….OK!
load mau.ko ….OK!
load ot_npu_device.ko ….OK!
load ot_npu_aicpu.ko ….OK!
load ot_npu_dfx.ko ….OK!
load ot_npu_tsfw.ko ….OK!

message recv thread run

ipcm detecting thread running!

load dsp.ko ….OK!
load sensor_spi.ko ….OK!
load hdmi.ko OK!
load mipi_tx.ko ….OK!
load aio.ko ….OK!
load ai.ko ….OK!
load ao.ko ….OK!
load aenc.ko ….OK!
load adec.ko ….OK!
load acodec.ko ….OK!
load mipi_rx.ko ….OK!
load ot_user ….OK!
load photo.ko ….OK!
load ot_cipher.ko ….OK!
usbcore: registered new interface driver usb_ch343
ch343: USB serial driver for ch342/ch343/ch344/ch9101/ch9102/ch9103, etc.
ch343: V1.1 On 2021.02.05
bsp-i2c 11060000.i2c: wait idle timeout, RIS: 0x10, SR: 0xa0000
ERROR:0
bsp-i2c 11060000.i2c: wait idle timeout, RIS: 0x10, SR: 0xa0000
ERROR:0
plat_soc:EMERG]0:emerg log.
plat_soc:ALERT]1:alert log.
plat_soc:CRIT]2:crit log.
plat_soc:E]3:err log.
plat_soc:W]4:warning log.
plat_soc:E]custom ini[plat kern log level]: 7.
plat_soc:E]board_power_gpio_init::succ, power_gpio_idx=[40]!
plat_soc:E]board_wakeup_gpio_init::succ, wkup_gpio_idx=[70]!
plat_soc:E]tcp rx task
[USB][I]OFF —> INIT
[usb_set_bus_state:90]
[USB][I]boot usb[oal_usb_probe:1322]
[USB][I]bulk_in_ep:0x81[oal_usb_boot_bulk_in_probe:1225]
[USB][I]dev->bulk_out_ep:0x1[oal_usb_boot_bulk_out_probe:1256]
[USB][I]INIT —> BOOT
[usb_set_bus_state:90]
[USB][I]usb boot probe success[oal_usb_boot_init_config:1297]
usbcore: registered new interface driver wireless_usb
plat_soc:E]hcc diag log service ini ok
[USB][E] usb_bulk_msg ret=-110[oal_usb_bulk_out_msg:933]
plat_soc:E]send msg [READM 0x40019000 4 ] failed, ret=-110
[USB][E] usb_bulk_msg ret=-110[oal_usb_bulk_out_msg:933]
plat_soc:E]send msg [READM 0x40019000 4 ] failed, ret=-110
[USB][E] usb_bulk_msg ret=-110[oal_usb_bulk_out_msg:933]
plat_soc:E]send msg [READM 0x40019000 4 ] failed, ret=-110
[USB][E] usb_bulk_msg ret=-110[oal_usb_bulk_out_msg:933]
plat_soc:E]send msg [READM 0x40019000 4 ] failed, ret=-110
[USB][E] usb_bulk_msg ret=-110[oal_usb_bulk_out_msg:933]