- 收藏
- 点赞
- 分享
- 举报
海思3519 换了内核启动就爆粗 求大神帮忙解决
sram to npu!
Booting Linux on physical CPU 0x0000000000 [0x412fd050]
Linux version 5.10.165 (csg@ubuntu) (aarch64-v01c01-linux-musl-gcc (GCC-10.3.0 musl-1.2.3 ver100.110 2023-06-09 09:00:00) 10.3.0, GNU ld (GNU Binutils) 2.38) #2 SMP Mon Dec 22 15:26:23 CST 2025
Machine model: Vendor HI3519DV500 DEMO Board
Memory limited to 400MB
Zone ranges:
DMA [mem 0x0000000040030000-0x000000005902ffff]
DMA32 empty
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000040030000-0x000000005902ffff]
Initmem setup node 0 [mem 0x0000000040030000-0x000000005902ffff]
On node 0, zone DMA: 976 pages in unavailable ranges
cma zone is not set!
cma: Reserved 4 MiB at 0x0000000058800000
psci: probing for conduit method from DT.
psci: PSCIv1.1 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: MIGRATE_INFO_TYPE not supported.
psci: SMC Calling Convention v1.2
percpu: Embedded 19 pages/cpu s40024 r8192 d29608 u77824
Detected VIPT I-cache on CPU0
CPU features: detected: GIC system register CPU interface
CPU features: detected: ARM errata 1165522, 1319367, or 1530923
Built 1 zonelists, mobility grouping on. Total pages: 100800
Kernel command line: mem=400M console=ttyAMA0,115200 clk_ignore_unused root=/dev/mmcblk0p6 rootfstype=ext4 ro rootwait blkdevparts=mmcblk0:1M(boot),512K(bl31),512K(otp),20M(kernel),512K(offset),201M(rootfs),200M(userdata),40M(PowerHarmony),40M(storage)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
mem auto-init: stack:off, heap alloc:off, heap free:off
Memory: 373020K/409600K available (9726K kernel code, 476K rwdata, 2280K rodata, 1408K init, 332K bss, 32484K reserved, 4096K cma-reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
rcu: Hierarchical RCU implementation.
rcu: RCU event tracing is enabled.
Tracing variant of Tasks RCU enabled.
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
GICv3: 320 SPIs implemented
GICv3: 0 Extended SPIs implemented
GICv3: Distributor has no Range Selector support
GICv3: 16 PPIs implemented
GICv3: CPU0: found redistributor 0 region 0:0x0000000012440000
arch_timer: cp15 timer(s) running at 24.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
Console: colour dummy device 80x25
Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
rcu: Hierarchical SRCU implementation.
smp: Bringing up secondary CPUs …
Detected VIPT I-cache on CPU1
GICv3: CPU1: found redistributor 100 region 0:0x0000000012460000
CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
smp: Brought up 1 node, 2 CPUs
SMP: Total of 2 processors activated.
CPU features: detected: Privileged Access Never
CPU features: detected: User Access Override
CPU features: detected: 32-bit EL0 Support
CPU features: detected: Common not Private translations
CPU features: detected: RAS Extension Support
CPU features: detected: Data cache clean to the PoU not required for I/D coherence
CPU features: detected: CRC32 instructions
CPU features: detected: Speculative Store Bypassing Safe (SSBS)
CPU: All CPU(s) started at EL1
alternatives: patching kernel code
devtmpfs: initialized
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 512 (order: 3, 32768 bytes, linear)
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
bbox:[info][blackbox_core.c:261] wait for log part [] begin!
bbox:[info][blackbox_core.c:266] wait for log part [] end!
DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
ASID allocator initialised with 65536 entries
Serial: AMBA PL011 UART driver
vgaarb: loaded
SCSI subsystem initialized
ssp-pl022 11070000.spi: deassert reset
ssp-pl022 11070000.spi: Failed to work in dma mode, work without dma!
ssp-pl022 11071000.spi: deassert reset
ssp-pl022 11071000.spi: Failed to work in dma mode, work without dma!
ssp-pl022 11072000.spi: deassert reset
ssp-pl022 11072000.spi: Failed to work in dma mode, work without dma!
ssp-pl022 11073000.spi: deassert reset
ssp-pl022 11073000.spi: Failed to work in dma mode, work without dma!
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
videodev: Linux video capture interface: v2.00
[UPS-PHY][ups_phy_module_init]registered new ups phy driver
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.22
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
clocksource: Switched to clocksource arch_sys_counter
VFS: Disk quotas dquot_6.6.0
VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
usbcore: registered new interface driver usb_ch343
ch341: USB serial driver for ch342/ch343/ch344/ch346/ch347/ch339/ch9101/ch9102/ch9103/ch9104/ch9143, etc.
ch341: V2.0 On 2025.09
NET: Registered protocol family 2
IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Initialise system trusted keyrings
workingset: timestamp_bits=62 max_order=17 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse: init (API version 7.32)
SGI XFS with ACLs, security attributes, realtime, quota, no debug enabled
Key type asymmetric registered
Asymmetric key parser ‘x509’ registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
io scheduler mq-deadline registered
io scheduler kyber registered
cacheinfo: Unable to detect cache hierarchy for CPU 0
brd: module loaded
loop: module loaded
bsp_nand: Failed to locate of_node [id: 0]
gmac_v200 10290000.ethernet: invalid resource
attached PHY 1 to driver Generic PHY, PHY_ID=0x1cc916
ETH: rgmii-id, phy_addr=1
usbcore: registered new interface driver asix
usbcore: registered new interface driver ax88179_178a
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver qmi_wwan
usbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
mousedev: PS/2 mouse device common for all mice
bsp_rtc 11110000.rtc: registered as rtc0
bsp_rtc 11110000.rtc: setting system clock to 1970-01-01T09:24:47 UTC (33887)
bsp_rtc 11110000.rtc: RTC driver for bsp enabled
i2c /dev entries driver
bsp-i2c 11060000.i2c: deassert reset
bsp-i2c 11060000.i2c: IRQ index 0 not found
bsp-i2c 11061000.i2c: deassert reset
bsp-i2c 11061000.i2c: IRQ index 0 not found
bsp-i2c 11062000.i2c: deassert reset
bsp-i2c 11062000.i2c: IRQ index 0 not found
bsp-i2c 11063000.i2c: deassert reset
bsp-i2c 11063000.i2c: IRQ index 0 not found
bsp-i2c 11064000.i2c: deassert reset
bsp-i2c 11064000.i2c: IRQ index 0 not found
bsp-i2c 11065000.i2c: deassert reset
bsp-i2c 11065000.i2c: IRQ index 0 not found
bsp-i2c 11066000.i2c: deassert reset
bsp-i2c 11066000.i2c: IRQ index 0 not found
bsp-i2c 11067000.i2c: deassert reset
bsp-i2c 11067000.i2c: IRQ index 0 not found
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ….
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
hilog_init Start0
[WING-USB][wing_usb_module_init]register wing usb driver
mmc0: SDHCI controller on 10020000.eMMC [10020000.eMMC] using ADMA 64-bit
mmc1: SDHCI controller on 10030000.SDIO [10030000.SDIO] using ADMA 64-bit
NET: Registered protocol family 10
Segment Routing with IPv6
NET: Registered protocol family 17
Loading compiled-in X.509 certificates
uart-pl011 11040000.uart: deassert reset
11040000.uart: ttyAMA0 at MMIO 0x11040000 (irq = 16, base_baud = 0) is a PL011 rev2
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
printk: console [ttyAMA0] enabled
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
uart-pl011 11041000.uart: deassert reset
xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe6d hci version 0x110 quirks 0x0000000000010010
11041000.uart: ttyAMA1 at MMIO 0x11041000 (irq = 17, base_baud = 0) is a PL011 rev2
xhci-hcd xhci-hcd.0.auto: irq 83, io mem 0x10320000
uart-pl011 11042000.uart: deassert reset
hub 1-0:1.0: USB hub found
11042000.uart: ttyAMA2 at MMIO 0x11042000 (irq = 18, base_baud = 0) is a PL011 rev2
hub 1-0:1.0: 1 port detected
uart-pl011 11043000.uart: deassert reset
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
11043000.uart: ttyAMA3 at MMIO 0x11043000 (irq = 19, base_baud = 0) is a PL011 rev2
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
uart-pl011 11044000.uart: deassert reset
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
11044000.uart: ttyAMA4 at MMIO 0x11044000 (irq = 20, base_baud = 0) is a PL011 rev2
usb usb2: We don’t know the algorithms for LPM for this host, disabling LPM.
pl061_gpio 11090000.gpio_chip: PL061 GPIO chip registered
hub 2-0:1.0: USB hub found
pl061_gpio 11091000.gpio_chip: PL061 GPIO chip registered
hub 2-0:1.0: 1 port detected
pl061_gpio 11092000.gpio_chip: PL061 GPIO chip registered
usb usb1-port1: over-current condition
pl061_gpio 11093000.gpio_chip: PL061 GPIO chip registered
usb usb2-port1: over-current condition
pl061_gpio 11094000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11095000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11096000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 11097000.gpio_chip: PL061 GPIO chip registered
mmc0: tuning done! valid phase shift [8, 5] Final Phase:22
pl061_gpio 11098000.gpio_chip: PL061 GPIO chip registered
mmc0: new HS400 MMC card at address 0001
pl061_gpio 11099000.gpio_chip: PL061 GPIO chip registered
mmcblk0: mmc0:0001 HAG2e 14.7 GiB
pl061_gpio 1109a000.gpio_chip: PL061 GPIO chip registered
mmcblk0boot0: mmc0:0001 HAG2e partition 1 4.00 MiB
pl061_gpio 1109b000.gpio_chip: PL061 GPIO chip registered
mmcblk0boot1: mmc0:0001 HAG2e partition 2 4.00 MiB
pl061_gpio 1109c000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 1109d000.gpio_chip: PL061 GPIO chip registered
pl061_gpio 1109e000.gpio_chip: PL061 GPIO chip registered
mmcblk0rpmb: mmc0:0001 HAG2e partition 3 4.00 MiB, chardev (249:0)
[I/osal_cdev] register hdf class success
[I/osal_cdev] add cdev dev_mgr success
[I/osal_cdev] add cdev devsvc_mgr success
[I/devmgr_service] start svcmgr result 0
[I/hcs_blob_if] CheckHcsBlobLength: the blobLength: 49048, byteAlign: 1
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver linux_gpio_adapter
[E/devhost_service_clnt] failed to AddDevice , ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_GPIO_MANAGER
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_GPIO_MANAGER, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_EMMC
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_MMC_0, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_SDIO
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_MMC_2, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_WATCHDOG
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_WATCHDOG_0, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_RTC
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_RTC, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_UART
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_UART_1, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_UART
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_UART_0, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_REGULATOR_MANAGER
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_REGULATOR_MANAGER, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_I2C_MANAGER
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_I2C_MANAGER, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver linux_regulator_adapter
[E/devhost_service_clnt] failed to AddDevice , ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver linux_i2c_adapter
[E/devhost_service_clnt] failed to AddDevice , ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_SPI
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_SPI_2, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_SPI
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_SPI_1, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_SPI
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_SPI_0, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_ADC_MANAGER
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_ADC_MANAGER, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver linux_adc_adapter
[E/devhost_service_clnt] failed to AddDevice , ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_PWM
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_PWM_1, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_PLATFORM_PWM
[E/devhost_service_clnt] failed to AddDevice HDF_PLATFORM_PWM_0, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_MIPI_TX
[E/devhost_service_clnt] failed to AddDevice HDF_MIPI_TX, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_DSOFTBUS
[E/devhost_service_clnt] failed to AddDevice hdf_dsoftbus, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_VIBRATOR
[E/devhost_service_clnt] failed to AddDevice hdf_misc_vibrator, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_LINEAR_VIBRATOR
[E/devhost_service_clnt] failed to AddDevice hdf_misc_linear_vibrator, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_SENSOR_MGR_AP
[E/devhost_service_clnt] failed to AddDevice hdf_sensor_manager_ap, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_WIFI
[E/devhost_service_clnt] failed to AddDevice hdfwifi, ret = -207
[I/device_node] launch devnode hdf_input_host
[I/HDF_LOG_TAG] HdfInputManagerInit: enter
[I/HDF_LOG_TAG] HdfInputManagerInit: exit succ
[I/osal_cdev] add cdev hdf_input_host success
mmcblk0: p1(boot) p2(bl31) p3(otp) p4(kernel) p5(offset) p6(rootfs) p7(userdata) p8(PowerHarmony) p9(storage)
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_TOUCH
[E/devhost_service_clnt] failed to AddDevice hdf_input_event1, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_TOUCH_GT911
[E/devhost_service_clnt] failed to AddDevice hdf_touch_gt911_service, ret = -207
[I/device_node] launch devnode
[I/HDF_LOG_TAG] LoadCachedHid: exit
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_BL
[E/devhost_service_clnt] failed to AddDevice hdf_bl, ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver PWM_BL
[E/devhost_service_clnt] failed to AddDevice , ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver LCD_ICN9700
[E/devhost_service_clnt] failed to AddDevice , ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HI351XX_DISP
[E/devhost_service_clnt] failed to AddDevice , ret = -207
[I/HDF_LOG_TAG] HdfDriverManagerGetDriver:try to dynamic load driver HDF_DISP
[E/devhost_service_clnt] failed to AddDevice hdf_disp, ret = -207
[I/hdf_power_manager] HdfPmTaskQueueInit HdfTaskQueueCreate success
cfg80211: Loading compiled-in X.509 certificates for regulatory database
cfg80211: Loaded X.509 cert ‘sforshee: 00b28ddf47aef9cea7’
clk: Not disabling unused clocks
ALSA device list:
No soundcards found.
platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
cfg80211: failed to load regulatory.db
uart-pl011 11040000.uart: no DMA platform data
List of all partitions:
0100 65536 ram0
(driver?)
0101 65536 ram1
(driver?)
0102 65536 ram2
(driver?)
0103 65536 ram3
(driver?)
0104 65536 ram4
(driver?)
0105 65536 ram5
(driver?)
0106 65536 ram6
(driver?)
0107 65536 ram7
(driver?)
0108 65536 ram8
(driver?)
0109 65536 ram9
(driver?)
010a 65536 ram10
(driver?)
010b 65536 ram11
(driver?)
010c 65536 ram12
(driver?)
010d 65536 ram13
(driver?)
010e 65536 ram14
(driver?)
010f 65536 ram15
(driver?)
b300 15392768 mmcblk0
driver: mmcblk
b301 1024 mmcblk0p1
b302 512 mmcblk0p2
b303 512 mmcblk0p3
b304 20480 mmcblk0p4
b305 512 mmcblk0p5
b306 205824 mmcblk0p6
b307 204800 mmcblk0p7
103:00000 40960 mmcblk0p8
103:00001 40960 mmcblk0p9
No filesystem could mount root, tried:
ext4
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,6)
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.165 #2
Hardware name: Vendor HI3519DV500 DEMO Board (DT)
Call trace:
dump_backtrace+0x0/0x1a0
show_stack+0x18/0x24
dump_stack+0xd4/0x110
panic+0x194/0x348
mount_block_root+0x370/0x3ac
mount_root+0x70/0x80
prepare_namespace+0x124/0x164
kernel_init_freeable+0x1fc/0x238
kernel_init+0x14/0x114
ret_from_fork+0x10/0x38
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x00040026,2a00a218
Memory Limit: 400 MB
—-[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,6) ]—-
设置的环境变量
setenv bootargs “mem=400M console=ttyAMA0,115200 clk_ignore_unused root=/dev/mmcblk0p6 rootfstype=ext4 ro rootwait blkdevparts=mmcblk0:1M(boot),512K(bl31),512K(otp),20M(kernel),512K(offset),201M(rootfs),200M(userdata),40M(PowerHarmony),40M(storage)”
setenv bootcmd “mmc read 0 0x40010000 0x800 0x400; ipcboot bl31 0x40010000;mmc read 0 0x44000000 0xc00 0x400;go 0x44000000; mmc read 0 0x44000000 0x1000 0xA000; verify_boot kernel 0x44000000 0x1000; ipcboot uimgfdt 0x44040c00;”
暂无数据Markdown 语法
- 加粗**内容**
- 斜体*内容*
- 删除线~~内容~~
- 引用> 引用内容
- 代码`代码`
- 代码块```编程语言↵代码```
- 链接[链接标题](url)
- 无序列表- 内容
- 有序列表1. 内容
- 缩进内容
- 图片
-
2018-12-06 16:11:42
-
2020-10-09 14:04:21
-
2021-03-25 17:40:27
-
2018-08-24 11:20:44
-
2018-12-13 13:46:07
-
2019-05-11 07:59:58
-
2016-08-08 10:41:49
-
2018-12-07 15:23:53
-
2016-07-19 16:59:00
-
2014-12-29 16:41:06
-
2019-05-21 11:02:36
-
2018-09-14 14:55:24
-
2020-06-12 11:21:54
-
2016-10-22 15:53:50
-
2018-09-08 09:11:33
-
2019-12-24 21:36:09
-
2017-01-23 10:49:30
-
2019-01-10 11:32:21
-
2015-11-10 10:40:56
-
10hi35169dv500平台使用http协议推拉流UVC摄像头,帧率问题
-
10hi3516cv610关于YOLO优化和调优问题
-
10hi_mpi_vpss_get_chn_frame err:0xa0078016报错
-
5gk7205v200(hisi3516ev200)如何接入b656?
-
30pipe管道创建失败
-
10atc转换模型失败
-
20拍摄静止画面显示正常,拍摄运动的画面出现马赛克显示
-
100hi3516cv610 通过易百纳官方SDK中编译出的uboot env kernel,移植到自己的工程中,MPP初始化时出现内核拷贝数据到用户端时出现错误导致内核进入pain模式进而时内核重启
-
5hisi3519 gs2972 bt1120 转sdi 无法正常显示问题
-
5hisi3516cv610 + gc4336p 夜晚很模糊
举报类型
- 内容涉黄/赌/毒
- 内容侵权/抄袭
- 政治相关
- 涉嫌广告
- 侮辱谩骂
- 其他
详细说明

微信扫码分享
QQ好友